Sprinter fault codes
4,904 codes · 824 vehicle records · 187 ECU records · 19,551 live-data parameters
Codes 4,904
| Code | Description | Brands | System |
|---|---|---|---|
| U1239 | Loss of serial communications for class 2 devices | 8 | Network |
| U1240 | Loss of serial communications for class 2 devices | 11 | Network |
| U1241 | Loss of serial communications for class 2 devices | 9 | Network |
| U1242 | Loss of serial communications for class 2 devices | 8 | Network |
| U1243 | Loss of serial communications for class 2 devices | 9 | Network |
| U1244 | Loss of serial communications for class 2 devices | 10 | Network |
| U1245 | Loss of serial communications for class 2 devices | 8 | Network |
| U1246 | Loss of serial communications for class 2 devices | 8 | Network |
| U1247 | Loss of serial communications for class 2 devices | 8 | Network |
| U1248 | Loss of serial communications for class 2 devices | 8 | Network |
| U1253 | Loss of serial communications for class 2 devices | 10 | Network |
| U1254 | Loss of serial communications for class 2 devices | 8 | Network |
| U1255 | Class 2 Communication Malfunction | 10 | Network |
| U1256 | Testeri vastus puudub | 6 | Network |
| U1257 | Rear fresh air blower control module | 4 | Network |
| U1258 | Satellite Antenna Circuit | 10 | Network |
| U1297 | Linker zijruitontdooierdeurmotor | 6 | Network |
| U1356 | No description available | 4 | Network |
| U1400 | Alternator LIN network failure | 27 | Network |
| U1401 | Scope present in vehicle - Connect connector to COMAND controller unit | 33 | Network |
| U1402 | Immobilizer message error | 21 | Network |
| U1403 | Retrofit is not included in further wiring diagrams | 19 | Network |
| U1404 | Immobilizer not matching | 18 | Network |
| U1405 | Dynamic Range Error | 22 | Network |
| U1406 | Dynamic Range Error | 17 | Network |
| U1407 | Dynamic Range Error | 22 | Network |
| U1408 | Dynamic Range Error | 15 | Network |
| U1409 | Dynamic Range Error | 13 | Network |
| U140A | Terminal 30: open circuit; Open or short to ground | 3 | Network |
| U140B | No description available | 8 | Network |
| U140C | No description available | 8 | Network |
| U140F | implausible engine variant data | 3 | Network |
| U1410 | Dynamic Range Error | 17 | Network |
| U1420 | Dynamic Range Error | 18 | Network |
| U1422 | I²C bus master request | 22 | Network |
| U1444 | Komunikacija s radarom IC C/U | 5 | Network |
| U1445 | Implausible data received from display screen module | 4 | Network |
| U1446E1 | GMS Fault - RDU shut-down failure | 2 | Network |
| U1446E2 | GMS Fault - GMS intervention is too long | 2 | Network |
| U1446E3 | No description available | 2 | Network |
| U1446FE | GMS Fault - Velocity failure | 2 | Network |
| U1446FF | GMS Fault - Gradient failure | 2 | Network |
| U1448 | Valid except code U10 | 5 | Network |
| U1453 | Valid as of facelift | 4 | Network |
| U1501 | ICM Redundant Data Re-sync Failure | 18 | Network |
| U1502 | SW row LIN timeout/Not equipped | 15 | Network |
| U1504 | RLS LIN timeout/Not equipped | 15 | Network |
| U1505 | CAN communication | 14 | Network |
| U1507 | LIN transmission bit error | 14 | Network |
| U1508 | Software is not compatible with the engine management ECU | 14 | Network |
Some brand data is extracted from diagnostic files and may contain manufacturer-specific wording. General SAE J2012 descriptions are used where available.