SsangYong fault codes
4,752 codes · 93 vehicle records · 0 ECU records · 0 live-data parameters
Codes 4,752
| Code | Description | Brands | System |
|---|---|---|---|
| P0D4601 | Current sampling adequacy judgment failure | 1 | Powertrain |
| P0D4802 | Charging overcurrent | 1 | Powertrain |
| P0D4812 | Discharge overcurrent | 1 | Powertrain |
| P0D4822 | Regenerative overcurrent | 1 | Powertrain |
| P0D4901 | Safety charging overcurrent (level 1) | 1 | Powertrain |
| P0D4902 | Safety charging overcurrent (level 2) | 1 | Powertrain |
| P0D4903 | Safety discharge overcurrent (level 1) | 1 | Powertrain |
| P0D5801 | Thermal runaway | 1 | Powertrain |
| P0D5901 | Battery voltage low | 1 | Powertrain |
| P0D5902 | Battery overvoltage | 1 | Powertrain |
| P0D5911 | Battery pack + voltage sensing circuit open or short to ground | 1 | Powertrain |
| P0D5912 | Battery pack + voltage sensing circuit (5 V) short to battery (+) | 1 | Powertrain |
| P0D6600 | Communication error with cell sampling unit (cell capture circuit) | 1 | Powertrain |
| P0D6700 | Battery sensor voltage error | 2 | Powertrain |
| P0D7600 | Battery (+) power failure | 1 | Powertrain |
| P0D7601 | Battery (+) power circuit open or short to ground | 1 | Powertrain |
| P0D7602 | Battery (+) power circuit power stage circuit short | 1 | Powertrain |
| P0D7801 | Battery (+) voltage low (critical) | 1 | Powertrain |
| P0D7901 | Battery (+) voltage low | 1 | Powertrain |
| P0D7902 | Battery (+) overvoltage | 1 | Powertrain |
| P0D8803 | Precharging timeout | 1 | Powertrain |
| P0D8902 | Precharging overcurrent | 1 | Powertrain |
| P0D8903 | Precharging resistor overtemperature | 1 | Powertrain |
| P0D9601 | High voltage controller (high voltage shutdown unit) circuit open or short to ground | 1 | Powertrain |
| P0D9602 | High voltage controller (high voltage shutdown unit) of 5 V power supply device circuit short | 1 | Powertrain |
| P0D9603 | High voltage controller (high voltage shutdown unit) insulation resistance diagnosis timeout | 1 | Powertrain |
| P0D9604 | High voltage controller (high voltage shutdown unit) of 5 V power supply device fusion | 1 | Powertrain |
| P0D9701 | Low insulation resistance value (insulation failure) | 1 | Powertrain |
| P0D9801 | Low insulation resistance value on either +pole/-pole (insulation failure) | 1 | Powertrain |
| P100000 | Faulty main processor | 4 | Powertrain |
| P100001 | program memory test failed | 2 | Powertrain |
| P100002 | Data memory test failed | 2 | Powertrain |
| P100003 | Software reset occurred | 2 | Powertrain |
| P100004 | Stack error reset occurred | 2 | Powertrain |
| P100005 | Multiple watchdog resets occurred | 2 | Powertrain |
| P100006 | Loop time fault occurred | 2 | Powertrain |
| P100009 | Main Processor Core Failure | 2 | Powertrain |
| P100044 | Main Processor Data Memory Failure | 2 | Powertrain |
| P100047 | Main Processor Watchdog Timer Failure | 2 | Powertrain |
| P100092 | Main Processor Software Flow Failure | 2 | Powertrain |
| P100100 | Master BSD updated | 4 | Powertrain |
| P100149 | Electric Gear Parking (EGP) ECU error | 2 | Powertrain |
| P100200 | No DTCs are set in the IEM, except from the DTC for failed/missing calibration, i.e. IEM | 4 | Powertrain |
| P100296 | Motor error (overheating, voltage error) | 2 | Powertrain |
| P100300 | Checksum mismatch (transmission control unit) | 2 | Powertrain |
| P100377 | Motor error (stuck, overcurrent) | 2 | Powertrain |
| P100400 | Counter mismatch (transmission control unit) | 2 | Powertrain |
| P100492 | Motor position sensor error | 2 | Powertrain |
| P100500 | Lever operating out of range | 2 | Powertrain |
| P10054B | Electric Gear Parking (EGP) ECU overheating | 1 | Powertrain |
Some brand data is extracted from diagnostic files and may contain manufacturer-specific wording. General SAE J2012 descriptions are used where available.