Mitsubishi fault codes
8,900 codes · 153 vehicle records · 40 ECU records · 0 live-data parameters
Codes 8,900
| Code | Description | Brands | System |
|---|---|---|---|
| P127F | Vhodno vezje brizgalke valja 9 | 10 | Powertrain |
| P1280 | ICP Circ Out of Range Low | 17 | Powertrain |
| P1281 | Engine is Cold Too Long | 21 | Powertrain |
| P1285 | Accelerator pedal position sensor 3 circuit | 24 | Powertrain |
| P1286 | Fuel injection air control valve circuit short to battery (+) | 29 | Powertrain |
| P1287 | Turbocharger bypass valve open | 25 | Powertrain |
| P128C | 4-2 NG: appears to be faulty | 11 | Powertrain |
| P128D | 2-2 NG: appears to be faulty | 11 | Powertrain |
| P1290 | Cold start fuel pressure too high (bank 1) | 26 | Powertrain |
| P1291 | Coolant temp sensor at radiator outlet (G83): signal too large; Open or short to ground | 21 | Powertrain |
| P1292 | Cold start fuel pressure too low (bank 1) | 23 | Powertrain |
| P1293 | Injector circuit low to high current transition time bank 1 | 22 | Powertrain |
| P1294 | Target Idle Not Reached | 18 | Powertrain |
| P1295 | No 5Vs to Throttle Pos Sens | 15 | Powertrain |
| P1296 | Error in Mapped Cooling System | 20 | Powertrain |
| P1297 | Pressure drop between turbo and throttle valve (check D.V.!) | 29 | Powertrain |
| P1298 | Injector driver module failure | 16 | Powertrain |
| P1299 | Cylinder Head Over Temperature Protection Active | 18 | Powertrain |
| P129A | Bank 1 camshaft 1 lock position | 7 | Powertrain |
| P129B | bank 2 (N276): open circuit; Defective | 13 | Powertrain |
| P129E | Crash switch | 11 | Powertrain |
| P12A0 | Fuel pump driver control module fuel pump speed circuit low duty cycle | 9 | Powertrain |
| P12A1 | Fuel Pump Driver Control Module Fuel Pump Speed Circuit High Duty Cycle | 12 | Powertrain |
| P12A2 | Fuel pump driver control module fuel pump speed circuit performance | 12 | Powertrain |
| P12A4 | Fuel Pump Driver Control Module Enable Circuit Low Voltage | 11 | Powertrain |
| P12A5 | Fuel pump driver control module enable circuit high voltage | 11 | Powertrain |
| P12A7 | No.3 cylinder injection low | 10 | Powertrain |
| P12A8 | Fuel pump control status signal message counter incorrect | 11 | Powertrain |
| P12AA | Cylinder 1 Alternative Fuel Injector High Control Circuit Low Voltage | 10 | Powertrain |
| P12AB | Cylinder 1 alternative fuel injector high control circuit high voltage | 10 | Powertrain |
| P12B3 | Cylinder 1 injection timing retarded | 10 | Powertrain |
| P12B4 | Cylinder 1 injection timing advanced | 10 | Powertrain |
| P1300 | Boost calibration fault | 35 | Powertrain |
| P1301 | Boost calibration high | 34 | Powertrain |
| P1302 | Boost calibration low | 32 | Powertrain |
| P1303 | Knock adjustment failure | 28 | Powertrain |
| P1304 | Speed limit | 25 | Powertrain |
| P1305 | Igniter circuit #2 | 29 | Powertrain |
| P1306 | Kickdown relay pull-in circuit | 26 | Powertrain |
| P1307 | Kickdown Relay Hold Circ | 18 | Powertrain |
| P1308 | A/C Clutch Circuit Fault | 19 | Powertrain |
| P1309 | Misfire Detection Monitor | 20 | Powertrain |
| P1310 | Ionization misfire detection module fault | 21 | Powertrain |
| P1313 | Misfire Cylinder 1 Emission Related | 20 | Powertrain |
| P1320 | Battery management system (BMS) performance invalid | 27 | Powertrain |
| P1334 | Fuel cutoff of cylinder 4 (due to misfire) to prevent damage to catalyst | 15 | Powertrain |
| P1335 | Crankshaft position sensor (reference) | 34 | Powertrain |
| P1336 | Engine torque monitor: control limit exceeded; Open circuit | 33 | Powertrain |
| P1340 | Cylinder 4 misfire | 30 | Powertrain |
| P1341 | Intake variable cam phase (VCP) target wheel diagnostic fault | 24 | Powertrain |
Some brand data is extracted from diagnostic files and may contain manufacturer-specific wording. General SAE J2012 descriptions are used where available.