JEEP fault codes
Coverage shown is Chrysler data: 1,656 codes · 51 vehicle records · 884 ECU records · 0 live-data parameters.
JEEP shares fault-code data with Chrysler. Data may not cover JEEP-specific systems.
Codes 1,656
| Code | Description | Brands | System |
|---|---|---|---|
| B1602 | Main relay status fault | 30 | Body |
| B1603 | Alternator charging failure | 27 | Body |
| B1612 | Sunlight sensor circuit short to power | 25 | Body |
| B1615 | Blowing foot temperature sensor circuit short to power/ground or open | 26 | Body |
| B1616 | RF mirror horizontal position feedback circuit range/performance | 17 | Body |
| B1617 | Clutch relay not closed | 15 | Body |
| B1618 | Clutch relay not released | 16 | Body |
| B1619 | DR lap pretensioner squib short | 15 | Body |
| B1620 | ECU performance | 21 | Body |
| B1621 | Driver side airbag circuit short to ground | 10 | Body |
| B1622 | Right mirror vertical position sensor circuit low | 20 | Body |
| B1623 | Ignition positive (+APC) relay failure | 19 | Body |
| B1700 | Odometer data fail | 21 | Body |
| B1701 | Transponder Antenna Fail | 25 | Body |
| B1712 | mirror switch input shorted to ground | 21 | Body |
| B1715 | Transmission MIL Fault | 16 | Body |
| B1716 | Passenger knee airbag impedance large | 16 | Body |
| B1724 | Falla Circuito 2 Control Motor Espejo | 19 | Body |
| B1815 | Engine start switch indicator light failure | 15 | Body |
| B1816 | Loss of hybrid powertrain status information or start authorization information from the engine electronic control unit | 16 | Body |
| B1817 | Starting circuit fault | 15 | Body |
| B1820 | driver recline rearward switch circuit malfunction | 21 | Body |
| B1824 | The Lock bolt Motor is not supplied in Direction unLock | 8 | Body |
| B1828 | Upshift paddle stuck | 13 | Body |
| B1831 | High frequency function failure | 19 | Body |
| B1923 | Left Hall sensor no signal | 19 | Body |
| B1924 | Right Hall sensor no signal | 15 | Body |
| B1928 | Rear seat L side pre-tensioner power supply short circuit | 9 | Body |
| B1B98 | PS. belt tension sensor low | 11 | Body |
| B1B99 | PS. belt tension sensor high | 5 | Body |
| B1B9A | No description available | 1 | Body |
| B1B9D | No description available | 7 | Body |
| B1B9F | No description available | 1 | Body |
| B1BA0 | Suspicious starting activity | 3 | Body |
| B1BA1 | DCDC Output1 Failure | 3 | Body |
| B1BA8 | OCM system out of calibration | 10 | Body |
| B1CB0 | No description available | 1 | Body |
| B1CB1 | No description available | 1 | Body |
| B1D9B | Interior Door Handle Proximity Alert And Status LED Module - Status LED | 3 | Body |
| B1E00 | Volume up switch stuck | 11 | Body |
| B1E01 | Channel up switch stuck fault | 9 | Body |
| B1E05 | Voice switch stuck | 4 | Body |
| B1E06 | Panoramic image switch stuck | 4 | Body |
| B1E08 | 1F = Antenna Coil Circuit Fault | 9 | Body |
| B1E0A | Right image switch stuck | 4 | Body |
| B1E0C | Rear image switch stuck | 4 | Body |
| B1E25 | Driver(CH1) defective | 10 | Body |
| B1E26 | Driver(CH2) defective | 3 | Body |
| B1E27 | Driver(CH3) defective | 4 | Body |
| B1E30 | No description available | 2 | Body |
Some brand data is extracted from diagnostic files and may contain manufacturer-specific wording. General SAE J2012 descriptions are used where available.