Hyundai fault codes
7,974 codes · 345 vehicle records · 168 ECU records · 0 live-data parameters
Codes 7,974
| Code | Description | Brands | System |
|---|---|---|---|
| B1587 | RL side impact sensor ID fault | 12 | Body |
| B1588 | B/UP capacitor up converter | 14 | Body |
| B1589 | B/UP capacitor down converter | 14 | Body |
| B1590 | Lf/driver mirror vertical position sensor circuit | 23 | Body |
| B1591 | Seat Backrest Blower Drive - Circuit Current Below Threshold | 20 | Body |
| B1592 | Left mirror vertical position sensor circuit low | 19 | Body |
| B1593 | Left mirror vertical position sensor circuit high | 14 | Body |
| B1594 | Control unit abnormal condition | 16 | Body |
| B1595 | FR impact sensor short | 20 | Body |
| B1596 | LF mirror vertical position feedback circuit range/performance | 21 | Body |
| B1597 | FR impact sensor grounding | 18 | Body |
| B15A0 | When the outside door handle switch is short to ground, PSD sets DTC | 12 | Body |
| B15A1 | When the inside door handle switch is short to ground, PSD sets DTC | 9 | Body |
| B15A2 | When the outside door handle switch is short to ground, PSD sets DTC | 10 | Body |
| B15A3 | When the inside door handle switch is short to ground, PSD sets DTC | 10 | Body |
| B15A4 | If RH sliding door latch is abnormal, PSD ECU sets DTC | 9 | Body |
| B15A5 | If LH sliding door latch is abnormal, PSD ECU sets DTC | 4 | Body |
| B15A6 | If RH inside door handle close switch is short to ground, PSD ECU sets DTC | 4 | Body |
| B15A7 | If LH inside door handle close switch is short to ground, PSD ECU sets DTC | 4 | Body |
| B1600 | Pressure failure | 28 | Body |
| B1601 | Central power switch positive terminal (+CPC) relay control failure | 28 | Body |
| B1602 | Main relay status fault | 30 | Body |
| B160200 | If CAN Error Signal is received, BCM sets DTC | 2 | Body |
| B1603 | Alternator charging failure | 27 | Body |
| B160300 | If B-CAN BUS OFF is detected, BCM sets DTC | 2 | Body |
| B1604 | DR pretensioner squib open | 23 | Body |
| B160400 | If BCM CAN message is not received, IGPM sets DTC | 2 | Body |
| B1605 | Battery charging status unit reset | 26 | Body |
| B160500 | If DDM CAN message is not received, IGPM sets DTC | 2 | Body |
| B1606 | Keyless Access Unit lost communication with MICU | 23 | Body |
| B1607 | The air outlet temperature sensor is open-circuited | 24 | Body |
| B160700 | If PSM CAN message is not received, IGPM sets DTC | 2 | Body |
| B1608 | Air speed control circuit short circuit | 17 | Body |
| B160800 | EOL alignment failed azimuth - range gate length adjustment time out | 2 | Body |
| B1609 | Keyless Access unit lost communication with MICU | 17 | Body |
| B160900 | If SJB CAN message is not received, IGPM sets DTC | 2 | Body |
| B160908 | The SCC Module sets DTC when SJB CAN message from CGW is invalid | 1 | Body |
| B160B | Load reduction command to 230 volt unit failed | 12 | Body |
| B160C | Driver frontal airbag resistance high | 4 | Body |
| B160D | Driver front airbag resistance value not exist | 4 | Body |
| B160E | No description available | 4 | Body |
| B1610 | Temperature control circuit short circuit | 26 | Body |
| B1611 | Keyless Access unit lost communication with Gauge Control Module | 16 | Body |
| B1612 | Sunlight sensor circuit short to power | 25 | Body |
| B1613 | Interior temperature sensor circuit short to power/ground or open | 22 | Body |
| B1614 | TFE6-Control unit self-test | 18 | Body |
| B1615 | Blowing foot temperature sensor circuit short to power/ground or open | 26 | Body |
| B1616 | RF mirror horizontal position feedback circuit range/performance | 17 | Body |
| B1617 | Clutch relay not closed | 15 | Body |
| B1618 | Clutch relay not released | 16 | Body |
Some brand data is extracted from diagnostic files and may contain manufacturer-specific wording. General SAE J2012 descriptions are used where available.