SsangYong fault codes
4,752 codes · 93 vehicle records · 0 ECU records · 0 live-data parameters
Codes 4,752
| Code | Description | Brands | System |
|---|---|---|---|
| P20060D | Swirl drive fault (short circuit) for negative duty cycle | 1 | Powertrain |
| P20060E | Swirl drive fault (undervoltage) for negative duty cycle | 1 | Powertrain |
| P200700 | Faulty TCU RAM CAN - controller 2 | 1 | Powertrain |
| P200701 | Pressure sensor: short circuit to positive | 1 | Powertrain |
| P200702 | Pressure sensor: short circuit to ground or open circuit | 1 | Powertrain |
| P200708 | Pressure sensor: signal implausible | 1 | Powertrain |
| P200800 | PCM sets DTC if the PCM detects open in VCM motor control circuit | 2 | Powertrain |
| P200801 | Swirl drive fault (open circuit) for negative duty cycle | 1 | Powertrain |
| P200808 | Heating of component right O2 sensor before TWC: heating capacity is too low | 1 | Powertrain |
| P200900 | Die Ansteuerung der Ladungsbewegungsklappe (Zylinderreihe 1) hat einen Kurzschluss nach Masse. | 3 | Powertrain |
| P200901 | Swirl drive fault (short circuit to ground) for negative duty cyle | 1 | Powertrain |
| P200908 | Heating of component right O2 sensor after TWC: heating capacity is too low | 1 | Powertrain |
| P200A00 | PCM sets DTC if the deviation between target and actual position of VCM flap is too large | 2 | Powertrain |
| P200A01 | Knock sensor system of ECU: check the diagnosis multiplexer | 1 | Powertrain |
| P200A02 | Knock sensor system of ECU: knock sensor | 1 | Powertrain |
| P200A04 | Swirl HB drive fault (over temperature) | 1 | Powertrain |
| P200A08 | Knock sensor system of ECU: analysis circuit is faulty | 1 | Powertrain |
| P200A0A | Swirl Position Short Circuit to GND | 1 | Powertrain |
| P200A4B | Swirl HB Drive Fault (Short Circuit to VBATT) | 1 | Powertrain |
| P200A85 | Swirl HB Drive Fault (Open Circuit) | 1 | Powertrain |
| P200B00 | Faulty TCU CPU (internal) | 1 | Powertrain |
| P200B01 | The efficiency of the right catalytic converter is insufficient (function chain) | 1 | Powertrain |
| P200C00 | Faulty TCU program control | 1 | Powertrain |
| P200C01 | Right O2 sensor before TWC aging, correction variable exceeded: delay time too long | 1 | Powertrain |
| P200C02 | Right O2 sensor before TWC aging, correction variable exceeded: delay time too short | 1 | Powertrain |
| P200D01 | Right O2 sensor before TWC: aging, period too long | 1 | Powertrain |
| P200D02 | Right O2 sensor before TWC: aging, cycle duration too short | 1 | Powertrain |
| P200E01 | Right O2 sensor after TWC: level is above applicable threshold | 1 | Powertrain |
| P200E02 | Right O2 sensor after TWC: level is below applicable threshold | 1 | Powertrain |
| P200F01 | Right O2 sensor before TWC: short circuit to positive | 1 | Powertrain |
| P200F04 | Right O2 sensor before TWC: open circuit | 1 | Powertrain |
| P200F08 | Right O2 sensor before TWC: short circuit in the signal line | 1 | Powertrain |
| P201000 | If short in motor control circuit or short to power in control circuit of VSA is detected, ECM sets DTC | 2 | Powertrain |
| P201001 | Swirl drive fault (short circuit to VBATT) for negative duty cycle | 1 | Powertrain |
| P201004 | Right O2 sensor after TWC: open circuit | 1 | Powertrain |
| P201008 | Right O2 sensor after TWC: short circuit in the signal line | 1 | Powertrain |
| P201100 | Faulty TCU variant coding | 1 | Powertrain |
| P201101 | Knock sensor 1, right: signal implausible (voltage is too high / short circuit to positive) | 1 | Powertrain |
| P201102 | Knock sensor 1, right: signal implausible (open circuit / short circuit to ground) | 1 | Powertrain |
| P201200 | Faulty TCU checksum | 1 | Powertrain |
| P201202 | Activated charcoal canister shut-off valve: mechanical defect or component purge control valve is permanently open | 1 | Powertrain |
| P201300 | Faulty TCU (internally) | 1 | Powertrain |
| P201302 | Major leak in purge system: hose in system not connected or filler cap open | 1 | Powertrain |
| P201400 | Swirl position: flag indicating an external fault (due to analogic to digital converter or vext supply) | 1 | Powertrain |
| P201402 | Purge control system has slight leak: leak in hose connection or shutoff valve of activated charcoal canister | 1 | Powertrain |
| P201500 | The swirl opened position learnt value is too high (dirty valve or too big dispersion) | 2 | Powertrain |
| P201501 | The absolute difference between the current swirl opened position learning and the average of the previous learnt values is too high | 1 | Powertrain |
| P201502 | Purge control system has leak (function chain): mechanical defect in component purge control valve | 1 | Powertrain |
| P201600 | If the position sensor of VSA output voltage is below threshold value for more than 2 sec., ECM sets DTC. This fault might be caused by open in power circuit or short to ground in signal circuit of VSA position sensor | 2 | Powertrain |
| P201601 | Self-Adaptation of mixture formation for right bank of cylinders is at limit value (at part load), enrichment over permissible limit | 1 | Powertrain |
Some brand data is extracted from diagnostic files and may contain manufacturer-specific wording. General SAE J2012 descriptions are used where available.