SsangYong fault codes
4,752 codes · 93 vehicle records · 0 ECU records · 0 live-data parameters
Codes 4,752
| Code | Description | Brands | System |
|---|---|---|---|
| C120000 | Functional failure detection (EPB latching failure) | 1 | Chassis |
| C120100 | WSS front-LH range / performance / intermittent | 1 | Chassis |
| C120101 | Brake switch error | 1 | Chassis |
| C120200 | If VCC5T_P is out of range after a time x the failure will be detect If VCC5T_P is out of range after a time x the failure will be detect(short cicuit to GND) | 2 | Chassis |
| C120201 | Electronic Stability Control (ESC) off switch signal error | 1 | Chassis |
| C120209 | Brake disk overheating (traction control system) | 1 | Chassis |
| C120300 | WSS front-RH open/short | 1 | Chassis |
| C120301 | Mode switch signal error | 1 | Chassis |
| C120400 | WSS front-RH range / performance / intermittent | 1 | Chassis |
| C120500 | Lane Keeping Assist System (LKAS) switch circuit open or short or stuck | 1 | Chassis |
| C120581 | CAN communication: instrument panel signal error | 1 | Chassis |
| C120600 | Ventil Plausibilitätsfehler | 2 | Chassis |
| C120601 | Electronic Parking Brake (EPB) switch signal error | 1 | Chassis |
| C120606 | Electronic Parking Brake (EPB) switch error | 1 | Chassis |
| C120700 | VAC-Sensor Gradientenfehler | 2 | Chassis |
| C12072A | Electronic Parking Brake (EPB) switch stuck | 1 | Chassis |
| C120800 | WSS rear-LH invalid/no signal | 1 | Chassis |
| C120801 | Auto hold switch stuck - circuit short to battery (+) | 1 | Chassis |
| C120900 | Service calibration is active. | 2 | Chassis |
| C120A11 | In case of LED right short to ground, is set to active | 2 | Chassis |
| C120B15 | In case of LED right short to battery or open, is set to active | 2 | Chassis |
| C120C11 | In case of LED left short to ground, is set to active | 2 | Chassis |
| C120D15 | In case of LED left short to battery or open, is set to active | 2 | Chassis |
| C121000 | Vacuum Consumption Monitoring fault | 2 | Chassis |
| C121100 | electrical monitoring of the sensor 2 in the vacuum chamber, i.e. signal is out of Range | 2 | Chassis |
| C121200 | Nullpunktoffset des Drucksignals P2 | 2 | Chassis |
| C121302 | Wheel speed sensor error | 1 | Chassis |
| C123500 | Primary pressure sensor - electrical error | 1 | Chassis |
| C123700 | Primary pressure sensor - signal error | 1 | Chassis |
| C125500 | HSI(Horizontal situation indicator) overturned | 1 | Chassis |
| C125800 | OBD relevant DTC in RBS. For detailed information read Fault Memory of RBS | 2 | Chassis |
| C125900 | OBD relevant DTC in RBS. For detailed information read Fault Memory of RBS | 2 | Chassis |
| C125901 | Steering angle sensor-electrical | 1 | Chassis |
| C126000 | Steering angle sensor circuit - signal error | 1 | Chassis |
| C1261 | LF hold valve solenoid | 27 | Chassis |
| C126204 | Temperature sensor error | 1 | Chassis |
| C126801 | Valve stuck | 1 | Chassis |
| C12687A | Master cylinder leakage detection | 1 | Chassis |
| C127400 | G sensor open/short | 1 | Chassis |
| C127500 | G sensor range/performance error installed system | 1 | Chassis |
| C127800 | Faulty FRT LH body acceleration sensor | 1 | Chassis |
| C127900 | Faulty FRT RH body acceleration sensor | 1 | Chassis |
| C128100 | The power supply of the travel sensor for the brake pedal is too low. | 2 | Chassis |
| C128200 | The power supply of the travel sensor for the brake pedal is too high. | 2 | Chassis |
| C128300 | Plausibilisierung zwischen externen LW (Bus) und dem aus internen Rotorlagewinkel | 2 | Chassis |
| C128400 | Abnormal acceleration sensor supply voltage | 1 | Chassis |
| C128500 | G sensor calibration error | 1 | Chassis |
| C128702 | Brake fluid error | 1 | Chassis |
| C129000 | Torque sensor signal error | 1 | Chassis |
| C129002 | Torque sensor signal error | 1 | Chassis |
Some brand data is extracted from diagnostic files and may contain manufacturer-specific wording. General SAE J2012 descriptions are used where available.