SsangYong fault codes
4,752 codes · 93 vehicle records · 0 ECU records · 0 live-data parameters
Codes 4,752
| Code | Description | Brands | System |
|---|---|---|---|
| C104202 | Wheel speed sensor rear-RH air gap | 1 | Chassis |
| C104300 | Fault in rear left wheel speed sensor(temporary) | 1 | Chassis |
| C104302 | Wheel speed sensor rear-RH speed jump | 1 | Chassis |
| C104400 | CAN2: Sensorcluster-Botschaft fehlt (CAN Timeout) | 3 | Chassis |
| C104500 | Wheel speed sensor rear-RH phase | 1 | Chassis |
| C104502 | Wheel speed sensor rear-RH phase | 1 | Chassis |
| C104600 | Wheel speed sensor rear-RH wrong install | 1 | Chassis |
| C104602 | Wheel speed sensor rear-RH wrong install | 1 | Chassis |
| C105087 | CAN communication: front corner radar communication error - timeout | 1 | Chassis |
| C105100 | Vehicle velocity sensor timeout signal | 1 | Chassis |
| C105101 | Preesure sensor open/short | 1 | Chassis |
| C105186 | Front/rear corner radar signal error | 1 | Chassis |
| C105200 | testpulse pressure sensor front left | 2 | Chassis |
| C105202 | Preesure sensor abnormal signal (offset/noise) | 1 | Chassis |
| C105300 | Osek Task3 Laufzeitfehler | 2 | Chassis |
| C105302 | Pressure sensor no-signal (stick) | 1 | Chassis |
| C105402 | Pressure sensor calibration missing | 1 | Chassis |
| C106100 | CAN Error: Steering Angle sensor Calibration | 1 | Chassis |
| C106104 | Steering angle sensor calibration | 1 | Chassis |
| C106200 | Delta detection vac1 to vac2 | 2 | Chassis |
| C106208 | Steering wheel angle sensor message not received | 1 | Chassis |
| C106300 | CAN communication: steering wheel angle sensor zero adjustment error | 1 | Chassis |
| C106302 | Steering Wheel Angle Sensor Signal Fault (Offset/Noise) | 1 | Chassis |
| C106308 | Steering angle sensor-electrical | 1 | Chassis |
| C106400 | CAN communication: steering wheel angle sensor signal error (noise) | 1 | Chassis |
| C106402 | Steering Wheel Angle Sensor Signal Fault (Stuck) | 1 | Chassis |
| C106500 | Steering Angle Sensor Circuit open/short | 1 | Chassis |
| C107100 | Electrical fault in longitudinal acceleration sensor(G-sensor) | 1 | Chassis |
| C107101 | G-sensor error | 1 | Chassis |
| C107200 | testpulse pressure sensor front right | 2 | Chassis |
| C107300 | Fault in sensor cluster(electrical) | 1 | Chassis |
| C107400 | G sensor fail (rolling count/ self test) | 1 | Chassis |
| C107500 | offset pressuresensor Front right | 2 | Chassis |
| C107504 | G sensor offset calibration | 1 | Chassis |
| C108000 | EPB failure detection (COA reset error) | 1 | Chassis |
| C108100 | CAN communication: yawing & G-sensor message not received | 1 | Chassis |
| C108108 | CAN communication: yawing & G-sensor message not received | 1 | Chassis |
| C108200 | CAN Error: Yaw & G sensor abnormal signal (offset/noise) | 1 | Chassis |
| C108202 | Yaw & G sensor abnormal signal (offset/noise) | 1 | Chassis |
| C108300 | CAN Error: Yaw & G sensor no-signal (stick) | 1 | Chassis |
| C108302 | Yaw & G sensor no-signal (stick) | 1 | Chassis |
| C108400 | CAN Error: Yaw & G sensor fail (rolling count/self test) | 1 | Chassis |
| C108401 | Yaw & G sensor fail (rolling count/self test) | 1 | Chassis |
| C110000 | Drehzahlsensor VL elektrischer Fehler | 2 | Chassis |
| C110100 | Radar Sensor Alignment | 3 | Chassis |
| C110101 | If the supply voltage to HECU is higher than specification, HECU sets DTC | 2 | Chassis |
| C110116 | Under voltage(B+) | 3 | Chassis |
| C110117 | If the supply voltage to LDWS ECU is higher than specification, LDWS ECU sets DTC | 2 | Chassis |
| C110200 | Mode button loose contact(ECS) | 3 | Chassis |
| C110201 | If the supply voltage to HECU is lower than specification, HECU sets DTC | 2 | Chassis |
Some brand data is extracted from diagnostic files and may contain manufacturer-specific wording. General SAE J2012 descriptions are used where available.