SsangYong fault codes
4,752 codes · 93 vehicle records · 0 ECU records · 0 live-data parameters
Codes 4,752
| Code | Description | Brands | System |
|---|---|---|---|
| B11A400 | FRT LH PAS sensor Tx/Rx fault detection | 1 | Body |
| B11A500 | RR RH PAS sensor Tx/Rx fault detection | 1 | Body |
| B11A600 | RR LH PAS sensor Tx/Rx fault detection | 1 | Body |
| B11A700 | RR center PAS sensor Tx/Rx fault detection | 1 | Body |
| B11A800 | CAN: communication interruption(bus off) | 1 | Body |
| B11A900 | CAN: emergency mode (limp home) | 1 | Body |
| B11AA00 | PTL sensor a-phase fault: open/short circuit to ground | 1 | Body |
| B11AB00 | PTL sensor b-phase fault: short circuit to B+ | 1 | Body |
| B11AC00 | PTL touch sensor (R) fault: open/short circuit to ground | 1 | Body |
| B11AD00 | PTL touch sensor (L) fault: short circuit to B+ | 1 | Body |
| B11AE00 | Defective PTL motor | 1 | Body |
| B11AF00 | CAN:[RAM] doesn't receive the message 'trunk open control' from [PASEM] | 1 | Body |
| B11B000 | Rear PAS buzzer on/off driver open load or ground short | 1 | Body |
| B11B100 | Rear PAS buzzer on/off driver over load | 1 | Body |
| B11B200 | Front center RH PAS sensor Tx/Rx fault detection | 1 | Body |
| B11B300 | Front center LH PAS sensor Tx/Rx fault detection | 1 | Body |
| B11B400 | Rear center RH PAS sensor Tx/Rx fault detection | 1 | Body |
| B11F400 | Faulty slide motor hall sensor detection | 1 | Body |
| B11F500 | Faulty slide motor operation detection | 1 | Body |
| B11F600 | Over current in slide motor | 1 | Body |
| B11F700 | Faulty recliner motor hall sensor detection | 1 | Body |
| B11F800 | Faulty recliner motor operation detection | 1 | Body |
| B11F900 | Over current in recliner motor | 1 | Body |
| B11FA00 | Faulty FRT tilt motor hall sensor detection | 1 | Body |
| B11FB00 | Faulty FRT tilt motor operation detection | 1 | Body |
| B11FC00 | Over current in FRT tilt motor | 1 | Body |
| B11FD00 | Faulty RR tilt motor hall sensor detection | 1 | Body |
| B11FE00 | Faulty RR tilt motor operation detection | 1 | Body |
| B11FF00 | Over current in RR tilt motor | 1 | Body |
| B120000 | Faulty ventilation motor | 1 | Body |
| B120009 | PCU Unlatch Fail | 1 | Body |
| B120100 | LH Anti-Pinch Sensor Fail | 1 | Body |
| B120200 | Ecu Configuration Error | 2 | Body |
| B120300 | CAN: emergency mode (limp home) | 1 | Body |
| B120309 | LH Spindle Hall Sensor Fail | 1 | Body |
| B120400 | CAN: communication interruption(bus off) | 1 | Body |
| B120409 | RH Spindle Hall Sensor Fail | 1 | Body |
| B120500 | Interior Switch Stuck Fail | 1 | Body |
| B120511 | Passenger airbag switch - short circuit to ground | 2 | Body |
| B120600 | In-Side Switch Stuck Fail | 1 | Body |
| B120611 | Driver Side Airbag - Short To Ground | 2 | Body |
| B120700 | Battery voltage value too low | 1 | Body |
| B12071C | Battery voltage value too low | 1 | Body |
| B120800 | Battery voltage value too high | 1 | Body |
| B12081C | Battery voltage value too high | 1 | Body |
| B120900 | Left side spindle motor overcurrent | 1 | Body |
| B120919 | Passenger Curtain Airbag - Cross Connect | 2 | Body |
| B121000 | If abnormal Front Left Sensor operation signal is detected, BCM sets DTC | 2 | Body |
| B121019 | Right spindle motor overcurrent | 1 | Body |
| B121100 | If abnormal Front Left Sensor operation signal is detected, BCM sets DTC | 2 | Body |
Some brand data is extracted from diagnostic files and may contain manufacturer-specific wording. General SAE J2012 descriptions are used where available.