Mitsubishi fault codes
8,900 codes · 153 vehicle records · 40 ECU records · 0 live-data parameters
Codes 8,900
| Code | Description | Brands | System |
|---|---|---|---|
| P1D07 | Motor temperature signal is abnormal | 11 | Powertrain |
| P1D08 | CPLD data abnormal | 10 | Powertrain |
| P1D09 | Motor control unit (MCU) chip component safety inspection abnormal - internal error in the component | 9 | Powertrain |
| P1D10 | Ignition lock voltage signal error | 11 | Powertrain |
| P1D11 | Motor overload fault | 16 | Powertrain |
| P1D12 | Bus overcurrent | 15 | Powertrain |
| P1D13 | Controller temperature sensor fault | 17 | Powertrain |
| P1D14 | Power network AC voltage too high | 9 | Powertrain |
| P1D15 | Power network AC voltage phase sequence error | 11 | Powertrain |
| P1D16 | Controller bus voltage exceeds limit value | 11 | Powertrain |
| P1D17 | DC side over-current | 9 | Powertrain |
| P1D18 | Power network AC over-current | 9 | Powertrain |
| P1D19 | Power module failure | 14 | Powertrain |
| P1D20 | Multi module handshake failure | 12 | Powertrain |
| P1D21 | Motor A phase current overload | 9 | Powertrain |
| P1D22 | Battery Charger Temperature Sensor Circuit Malfunction | 14 | Powertrain |
| P1D23 | Phase current sensor failure | 14 | Powertrain |
| P1D24 | Power circuit | 14 | Powertrain |
| P1D25 | Shift control rationality | 17 | Powertrain |
| P1D26 | DC/DC current limiting protection | 8 | Powertrain |
| P1D27 | PFC temperature | 9 | Powertrain |
| P1D28 | Temperature in inverter circuit 1 | 14 | Powertrain |
| P1D29 | Pinge muundur 2 vooluring | 10 | Powertrain |
| P1D30 | This procedure deletes the DTC P1C5F and (Too low viscosity) immediately after the procedure has been performed. | 17 | Powertrain |
| P1D31 | ROM/RAM failure | 12 | Powertrain |
| P1D32 | EEPROM fail | 13 | Powertrain |
| P1D33 | AD converter abnormal | 12 | Powertrain |
| P1D34 | Gagal sensor arus input | 12 | Powertrain |
| P1D35 | Tulovirta-anturin vika | 11 | Powertrain |
| P1D36 | EV remotest signal abnormal | 13 | Powertrain |
| P1D37 | Internal control module software reset 2 active | 13 | Powertrain |
| P1D38 | Internal control module level 2 injection cut off active | 14 | Powertrain |
| P1D39 | Sinal IGCT-FDE anormal | 13 | Powertrain |
| P1D40 | Suhu gegelung penyearah | 15 | Powertrain |
| P1D41 | Motor rotor resistance stored value invalid | 12 | Powertrain |
| P1D42 | Motor position angle storage value invalid | 11 | Powertrain |
| P1D43 | RCM (sunroof motor) cannot be read | 11 | Powertrain |
| P1D44 | Motor B phase current sampling circuit fault | 15 | Powertrain |
| P1D45 | Motor C phase current sampling circuit fault | 13 | Powertrain |
| P1D46 | Torque request value comparison error | 14 | Powertrain |
| P1D47 | Torque request CAN value verification error | 14 | Powertrain |
| P1D48 | Bus voltage CAN value exceeds the valid range | 15 | Powertrain |
| P1D49 | Accelerator pedal circuit fault | 15 | Powertrain |
| P1D50 | Inductance over-temperature | 13 | Powertrain |
| P1D51 | AC input voltage sensor (2) low | 13 | Powertrain |
| P1D52 | Internal circuit (1) | 13 | Powertrain |
| P1D53 | Internal circuit (2) | 8 | Powertrain |
| P1D54 | Power network AC voltage too high | 5 | Powertrain |
| P1D55 | Power network AC voltage phase sequence error | 14 | Powertrain |
| P1D56 | ESD hold circuit | 16 | Powertrain |
Some brand data is extracted from diagnostic files and may contain manufacturer-specific wording. General SAE J2012 descriptions are used where available.