Isuzu fault codes
6,918 codes · 5 vehicle records · 107 ECU records · 0 live-data parameters
Codes 6,918
| Code | Description | Brands | System |
|---|---|---|---|
| P1072 | Ambient temperature sensor circuit intermittent low voltage | 20 | Powertrain |
| P1073 | Data conformity | 21 | Powertrain |
| P1074 | Ambient temperature sensor signal is implausible (low) | 21 | Powertrain |
| P1075 | Overload protection | 22 | Powertrain |
| P1076 | Temperature, servomotor, too high | 20 | Powertrain |
| P1077 | Temperature, servomotor, too high | 20 | Powertrain |
| P1078 | Activation current, servomotor, too high | 26 | Powertrain |
| P1079 | Luftmasse vor DK im Leerlauf unplaus. Niedrig | 17 | Powertrain |
| P107A | Pressure Regulator | 14 | Powertrain |
| P107B | Boost pressure adjustment | 14 | Powertrain |
| P1080 | Luftmasse vor DK Teillast unplaus. Hoch | 22 | Powertrain |
| P1081 | Stop/start capacitor control module battery negative circuit driver 1 high voltage | 21 | Powertrain |
| P1082 | Fuel filter pressure sensor performance | 21 | Powertrain |
| P1083 | Module 3 (cell 4) voltage under flow | 22 | Powertrain |
| P1084 | Pressure relief valve stick | 26 | Powertrain |
| P1085 | range 1: Lean limit exceeded; Lower limit exceeded | 21 | Powertrain |
| P1086 | range 2: Lean limit exceeded; Open or short to plus | 22 | Powertrain |
| P1087 | range 1: rich limit exceeded; Mechanical failure | 23 | Powertrain |
| P1088 | range 2: rich limit exceeded; Open circuit | 22 | Powertrain |
| P1089 | Tumble generator valve #1 (RH) position sensor circuit high input | 22 | Powertrain |
| P1090 | VVEL actuator motor (bank 1) | 22 | Powertrain |
| P1091 | VVEL actuator motor power | 25 | Powertrain |
| P1092 | MAF2: Electrical fault | 22 | Powertrain |
| P1093 | Fuel system malfunction | 26 | Powertrain |
| P1094 | Module 1 (cell 5) voltage over flow | 24 | Powertrain |
| P1095 | Rail pressure malfunction | 23 | Powertrain |
| P1096 | Module 1 (cell 7) voltage over flow | 21 | Powertrain |
| P1097 | EVAP purge system performance | 20 | Powertrain |
| P1098 | EVAP purge system performance | 19 | Powertrain |
| P1099 | Generator coil W current sensor 3 | 20 | Powertrain |
| P109A | This Adjustment is used when detected DTC or P253F | 8 | Powertrain |
| P10B2 | Monitoring of fuel injector for cylinder 2: malfunction detected; No or incorrect basic setting / adaptation | 17 | Powertrain |
| P10BC | NO. 189 battery voltage sampling wire loop fault | 9 | Powertrain |
| P1100 | Mass Air Flow Sensor Intermittent | 31 | Powertrain |
| P1101 | Mass Air Flow Sensor Out of Self-Test Range | 35 | Powertrain |
| P1102 | Mass Air Flow Sensor In Range But Lower Than Expected | 33 | Powertrain |
| P1103 | Mass Air Flow Sensor In Range But Higher Than Expected | 32 | Powertrain |
| P1104 | Signal too small | 31 | Powertrain |
| P1105 | The intake air pressure sensor signal is implausible when the engine is not running. | 37 | Powertrain |
| P1106 | Manifold Absolute Pressure Sensor Circuit Intermittent Low Voltage | 31 | Powertrain |
| P1107 | Manifold Absolute Pressure Sensor Circuit Intermittent High Voltage | 30 | Powertrain |
| P1108 | Intake air pressure sensor circuit voltage high intermittently | 27 | Powertrain |
| P1109 | The intake air pressure sensor signal is implausible when the engine is running | 27 | Powertrain |
| P110A | NO. 267 battery voltage sampling wire loop fault | 16 | Powertrain |
| P110B | NO. 268 battery voltage sampling wire loop fault | 16 | Powertrain |
| P110C | NO. 269 battery voltage sampling wire loop fault | 15 | Powertrain |
| P110D | NO. 270 battery voltage sampling wire loop fault | 16 | Powertrain |
| P110E | Water temperature sensor voltage signal too high | 17 | Powertrain |
| P1110 | Intake timing control (bank 1) | 32 | Powertrain |
| P1111 | Supercharged intake air temperature (IAT) sensor signal is implausible (high) | 32 | Powertrain |
Some brand data is extracted from diagnostic files and may contain manufacturer-specific wording. General SAE J2012 descriptions are used where available.