Hyundai fault codes
7,974 codes · 345 vehicle records · 168 ECU records · 0 live-data parameters
Codes 7,974
| Code | Description | Brands | System |
|---|---|---|---|
| C0077 | Low Tire Pressure | 22 | Chassis |
| C0078 | Tire Diameter | 28 | Chassis |
| C0079 | Variable effort steering | 19 | Chassis |
| C0080 | LR ABS solenoid #1 circuit malfunction | 8 | Chassis |
| C0081 | ABS Malfunction Indicator | 23 | Chassis |
| C0082 | Brake System Malfunction Indicator | 23 | Chassis |
| C0083 | Tire Pressure Monitor Malfunction Indicator | 22 | Chassis |
| C0084 | Traction active indicator | 19 | Chassis |
| C0085 | Traction disable indicator | 21 | Chassis |
| C0086 | Vehicle dynamics indicator | 19 | Chassis |
| C0089 | TCS Disable Switch | 22 | Chassis |
| C008A | TCS mode control | 20 | Chassis |
| C0090 | RR ABS solenoid #1 circuit malfunction | 10 | Chassis |
| C0095 | Brake switch circuit open | 12 | Chassis |
| C0110 | ABS Pump Motor Circuit | 10 | Chassis |
| C0121 | Défaut circuit relais soupapes | 13 | Chassis |
| C0161 | ABS brake switch circuit | 11 | Chassis |
| C0245 | EBCM control valve circuit | 11 | Chassis |
| C0550 | Vacuum sensor 'B' circuit high | 13 | Chassis |
| C0800 | Device power #1 circuit malfunction | 10 | Chassis |
| C0930 | No description available | 2 | Chassis |
| C0931 | System thermal high | 6 | Chassis |
| C1001 | Tandem brake master cylinder, pressure: Plausibility | 22 | Chassis |
| C1011 | Tandem brake master cylinder, pressure sensor 2: Signal offset | 21 | Chassis |
| C1012 | Tandem brake master cylinder, pressure sensor 1: General electrical fault | 22 | Chassis |
| C1014 | Brake System Total Volume Balance | 21 | Chassis |
| C1017 | Boot/trunk primary switch | 16 | Chassis |
| C1100 | Power restart | 21 | Chassis |
| C1101 | Battery voltage high | 25 | Chassis |
| C110101 | If the supply voltage to HECU is higher than specification, HECU sets DTC | 2 | Chassis |
| C110117 | If the supply voltage to LDWS ECU is higher than specification, LDWS ECU sets DTC | 2 | Chassis |
| C1102 | Battery voltage low | 24 | Chassis |
| C110201 | If the supply voltage to HECU is lower than specification, HECU sets DTC | 2 | Chassis |
| C110216 | If the supply voltage to LDWS ECU is lower than specification, LDWS ECU sets DTC | 2 | Chassis |
| C1103 | Longitudinal acceleration sensor electrical failure | 21 | Chassis |
| C110301 | The EPB Module sets DTC when CAN IG signal via Engine ECM is entered but hardware IG signal is not input | 1 | Chassis |
| C1104 | Brake bedding mode | 17 | Chassis |
| C1105 | Brake lamp control | 18 | Chassis |
| C1106 | Tire Size Mismatch | 19 | Chassis |
| C1107 | Diag C I B U S C M T O | 19 | Chassis |
| C1108 | Diag C I B U S C M T O | 18 | Chassis |
| C1109 | Diag C I B U S C M B Z E2 E | 19 | Chassis |
| C110A | Front vertical acceleration sensor | 14 | Chassis |
| C110B | Rear vertical acceleration sensor | 14 | Chassis |
| C1111 | Control lateral acceleration | 25 | Chassis |
| C1112 | Hood hydraulic pump relay 1 | 23 | Chassis |
| C1113 | Hood Hydraulic Pump Relay 2 - J588 | 23 | Chassis |
| C1114 | Roll axis torque | 22 | Chassis |
| C1121 | Damper solenoid | 23 | Chassis |
| C1122 | Front Latch Motor - Timeout | 23 | Chassis |
Some brand data is extracted from diagnostic files and may contain manufacturer-specific wording. General SAE J2012 descriptions are used where available.