Daihatsu fault codes
1,677 codes · 35 vehicle records · 41 ECU records · 0 live-data parameters
Codes 1,677
| Code | Description | Brands | System |
|---|---|---|---|
| P1572 | Left engine Mount solenoid valve short to ground | 33 | Powertrain |
| P1574 | Stop lamp switch circuit | 29 | Powertrain |
| P1575 | Right engine mount solenoid valve (N145): short to plus | 29 | Powertrain |
| P1576 | Pedal position not available | 27 | Powertrain |
| P1577 | Pedal position sensor outputs disagree | 27 | Powertrain |
| P1578 | ETC power less than demand | 22 | Powertrain |
| P1579 | ETC in power limiting mode | 29 | Powertrain |
| P1580 | DME: Activation, engine throttle | 30 | Powertrain |
| P1581 | Electronic throttle monitor malfunction | 23 | Powertrain |
| P1582 | Idle adaptation at limit | 21 | Powertrain |
| P1585 | Vacuum pump overload | 21 | Powertrain |
| P1586 | Electronic throttle to PCM communication error | 22 | Powertrain |
| P1587 | Engine mount solenoid valves short to ground | 22 | Powertrain |
| P1588 | Engine mount solenoid valves open circuit | 23 | Powertrain |
| P1589 | Throttle control unable to control to desired throttle angle | 22 | Powertrain |
| P1600 | Power supply (B+) terminal 15 low voltage | 31 | Powertrain |
| P1601 | ECU processor Analog/Digital Converter fault | 36 | Powertrain |
| P1602 | Control unit faulty | 35 | Powertrain |
| P1603 | Function monitoring, torque comparison | 35 | Powertrain |
| P1604 | Control unit faulty | 35 | Powertrain |
| P1605 | ECU processor fault | 37 | Powertrain |
| P1606 | ASW requests controller reset | 32 | Powertrain |
| P1607 | HW requests controller reset | 32 | Powertrain |
| P1608 | Clutch actuator high temperature | 32 | Powertrain |
| P1609 | Crash shutdown activated | 31 | Powertrain |
| P160A | ECU processor fault | 29 | Powertrain |
| P160B | A/D converter (system electronic failure) | 19 | Powertrain |
| P1610 | Linear power controller (LPC) fault | 38 | Powertrain |
| P1611 | Timeout time reached | 36 | Powertrain |
| P1612 | Immobilizer no or wrong signal | 39 | Powertrain |
| P1615 | Interactive Reprogramming Code - replace module | 36 | Powertrain |
| P1616 | Interactive Reprogramming Code - Diagnose Further | 35 | Powertrain |
| P1617 | CAN controller DPRAM (dual channel RAM) fault | 34 | Powertrain |
| P1618 | Check for the presence of DTC(Diagnostic Trouble Codes) P1616 and | 31 | Powertrain |
| P1619 | Short circuit to negative or open circuit | 33 | Powertrain |
| P161A | Glow plug control module not programmed | 23 | Powertrain |
| P161B | Control module torque performance | 24 | Powertrain |
| P1620 | Short circuit to positive | 33 | Powertrain |
| P1621 | System fault | 31 | Powertrain |
| P1625 | Voltage regulator, pedal-travel sensor-potentiometer faulty | 35 | Powertrain |
| P1626 | Theft Deterrent Fuel Enable Signal Lost | 32 | Powertrain |
| P1627 | Torque requirement requested by the driver not be followed | 25 | Powertrain |
| P1630 | Inconsistent request for cruise control | 32 | Powertrain |
| P1631 | Theft Deterrent Start Enable Signal Not Correct | 33 | Powertrain |
| P1632 | Adaptation conditions infringed | 28 | Powertrain |
| P1633 | Fault during test, limp-home point | 30 | Powertrain |
| P1634 | Closing spring faulty | 31 | Powertrain |
| P1635 | Stop learning during first initialisation aborted | 31 | Powertrain |
| P1636 | Throttle activation fault | 29 | Powertrain |
| P1637 | Deviation check | 32 | Powertrain |
Some brand data is extracted from diagnostic files and may contain manufacturer-specific wording. General SAE J2012 descriptions are used where available.