Results for “C110”
Fault codes 57
Results match keywords in the stored descriptions. Codes you typed are shown first.
| Code | Description | Brands | System |
|---|---|---|---|
| C11009D | The control unit 'radar sensor system' has a malfunction. The component or the system has undertemperature. | 1 | Chassis |
| C110100 | Radar Sensor Alignment | 3 | Chassis |
| C110101 | If the supply voltage to HECU is higher than specification, HECU sets DTC | 2 | Chassis |
| C110109 | No description available | 2 | Chassis |
| C110111 | Lane keeping assistant windscreen heater | 1 | Chassis |
| C110112 | Lane keeping assistant windscreen heater - short to positive | 1 | Chassis |
| C110115 | Lane keeping assistant windscreen heater - open circuit/short to positive | 1 | Chassis |
| C110116 | Under voltage(B+) | 3 | Chassis |
| C110117 | If the supply voltage to LDWS ECU is higher than specification, LDWS ECU sets DTC | 2 | Chassis |
| C11014B | No description available | 1 | Chassis |
Show 15 more matches on this page
| Code | Description | Brands | System |
|---|---|---|---|
| C110155 | No description available | 2 | Chassis |
| C110200 | Mode button loose contact(ECS) | 3 | Chassis |
| C110201 | If the supply voltage to HECU is lower than specification, HECU sets DTC | 2 | Chassis |
| C110216 | If the supply voltage to LDWS ECU is lower than specification, LDWS ECU sets DTC | 2 | Chassis |
| C110217 | Over voltage(B+) | 3 | Chassis |
| C110300 | No fault relating to - ACC sensor misaligned - entered, but other faults are entered | 4 | Chassis |
| C110301 | The EPB Module sets DTC when CAN IG signal via Engine ECM is entered but hardware IG signal is not input | 1 | Chassis |
| C110400 | Der MMR Front Slave meldet einen Fehler. | 4 | Chassis |
| C110500 | Sensor Supply Voltage Fault | 1 | Chassis |
| C110501 | Sensor Supply Voltage Fault | 1 | Chassis |
| C110600 | Signal Value out of valid range | 2 | Chassis |
| C110601 | No vehicle power signal | 1 | Chassis |
| C1106F0 | Dynamic calibration Limit value exceeded | 1 | Chassis |
| C110700 | Falsche Art von Raddrehzahlsensor VL erkannt | 2 | Chassis |
| C110777 | Electronic Parking Brake (EPB) actuator status error | 1 | Chassis |
| Code | Description | Brands | System |
|---|---|---|---|
| C110155 | No description available | 2 | Chassis |
| C110200 | Mode button loose contact(ECS) | 3 | Chassis |
| C110201 | If the supply voltage to HECU is lower than specification, HECU sets DTC | 2 | Chassis |
| C110216 | If the supply voltage to LDWS ECU is lower than specification, LDWS ECU sets DTC | 2 | Chassis |
| C110217 | Over voltage(B+) | 3 | Chassis |
| C110300 | No fault relating to - ACC sensor misaligned - entered, but other faults are entered | 4 | Chassis |
| C110301 | The EPB Module sets DTC when CAN IG signal via Engine ECM is entered but hardware IG signal is not input | 1 | Chassis |
| C110400 | Der MMR Front Slave meldet einen Fehler. | 4 | Chassis |
| C110500 | Sensor Supply Voltage Fault | 1 | Chassis |
| C110501 | Sensor Supply Voltage Fault | 1 | Chassis |
| C110600 | Signal Value out of valid range | 2 | Chassis |
| C110601 | No vehicle power signal | 1 | Chassis |
| C1106F0 | Dynamic calibration Limit value exceeded | 1 | Chassis |
| C110700 | Falsche Art von Raddrehzahlsensor VL erkannt | 2 | Chassis |
| C110777 | Electronic Parking Brake (EPB) actuator status error | 1 | Chassis |
Advanced: scanner vehicle and live-data matches
Vehicles 2
Vehicle data covers only some brands. These matches come from scanner data, not from a full vehicle index, so treat them as approximate.
| Brand | Model / variant | Details |
|---|---|---|
| Peugeot | MP_COMPTEUR_APPARITION_DEFAUT_C110A_51 | |
| Porsche | No active fault codes stored except: “C110B54 Calibration“ and “ Data bus – message implausible“ | code U112200 |
Live data 1
| Brand | Parameter | Units | Min | Max |
|---|---|---|---|---|
| Peugeot | MP_COMPTEUR_APPARITION_DEFAUT_C110A_51 | - | 0 | - |
These tables come from diagnostic data. They are useful for advanced users and can be ignored for a normal code lookup.