Fault code lookup

PowertrainP1D0B

Caution

Severity: Caution - get it checked when you can

Low voltage overvoltage

8 brands affected · Description from Toyota data.

Key terms: Control module: a small computer that runs one part of the car · Powertrain: engine, transmission and emissions

1What it means in plain English

The engine or powertrain control system has stored a fault that does not have specific guidance in this database yet.

2Common causes

  1. Sensor or actuator fault
  2. Wiring or connector fault
  3. Vacuum or intake leak
  4. Fuel or ignition problem
  5. Control module fault

3Can I drive?

Caution · drive with care

Have it diagnosed promptly. If the car runs and drives normally, drive gently to a workshop. If it runs badly, stalls, overheats, loses oil pressure, or a warning light is flashing or red, stop safely and get professional help. If the code concerns the brakes, brake vacuum or brake assist, do not drive until it is checked: a hard pedal or longer stopping distance means stop.

This page gives general information. It is not professional advice. For a definite diagnosis and a repair quote, ask a qualified mechanic to inspect the car.

4Brand data 8

BrandCodeDescriptionSystem
Mercedes-BenzP1D0BNo description available Powertrain
BYDP1D0BMotor phase loss fault BrandPowertrain
DFFSP1D0BLow voltage overvoltage BrandPowertrain
EOBDP1D0BAmaran voltan bekalan pengawal tinggi BrandPowertrain
HondaP1D0BNo description available Powertrain
HyundaiP1D0BNo description available Powertrain
ProtonP1D0BNo description available Powertrain
ToyotaP1D0BLow voltage overvoltage BrandPowertrain

Legend: SAE is the generic J2012 description; Brand is text taken from that manufacturer’s data. Manufacturer rows keep the wording and language of the source data, and non-English text is tagged so screen readers pronounce it correctly.

5Extended variant codes 20

These 7-character codes are manufacturer-specific variants of P1D0B and may be reported by some scan tools.

BrandCodeDescriptionSystem
Mercedes-BenzP1D0B00The internal power supply has a malfunction. BrandPowertrain
Mercedes-BenzP1D0B01The internal power supply has a malfunction. General Electrical Failure. Under/Over voltage on 1.8V DASy ECU Ethernet Switch internal voltage BrandPowertrain
Mercedes-BenzP1D0B14The internal P3V3 regulator voltage over 2.8v BrandPowertrain
Mercedes-BenzP1D0B16Secondary supply voltage under- overvoltage error at VCC/VEE of the LowSide ASICs. At least one LowSide ASIC report either VEE_UV/OV_ERR or LDO_VCC_UV/OV_ERR bit set in error register 1 BrandPowertrain
Mercedes-BenzP1D0B18Lo Range check for ISnsrElectcFuse BrandPowertrain
Mercedes-BenzP1D0B19Hi Range check for ISnsrElectcFuse BrandPowertrain
Mercedes-BenzP1D0B1CThe internal power supply has a malfunction. The voltage value is outside the permissible range. BrandPowertrain
Mercedes-BenzP1D0B1DDetection of an short circuit event on T30 based E-Fuse BrandPowertrain
Mercedes-BenzP1D0B29E-Fuse current measurement check BrandPowertrain
Mercedes-BenzP1D0BE0No description available Powertrain
Mercedes-BenzP1D0BE1The internal power supply has a malfunction. uP SVID value comparison mismatch BrandPowertrain
Mercedes-BenzP1D0BE3ECU Internal power supply 4V2 undervoltage failure BrandPowertrain
Mercedes-BenzP1D0BE4ECU Internal power supply 4V2 overvoltage failure BrandPowertrain
Mercedes-BenzP1D0BE6Fusion-internal VDD_CORE voltage monitoring signalizes error. Interne Spannungsberwachung der VDD_CORE-Spannung des Fusion signalisiert Fehler BrandPowertrain
Mercedes-BenzP1D0BE7AVS setting of voltage not correct BrandPowertrain
Mercedes-BenzP1D0BFAInternal Supply Error PLC - Development BrandPowertrain
Mercedes-BenzP1D0BFBOvervoltage Usky detected - Development BrandPowertrain
Mercedes-BenzP1D0BFCMalfunction Sky converter - Development BrandPowertrain
Mercedes-BenzP1D0BFDOvervolltage primary circuit - Development BrandPowertrain
Mercedes-BenzP1D0BFFDie interne Spannungsversorgung hat Funktionsstörung. BrandPowertrain

6Related codes

Browse Pxxx codes or P1D0xx codes.

OpenDTC - independent fault code reference