RELY fault codes
Coverage shown is Chery data: 8,313 codes · 74 vehicle records · 0 ECU records · 0 live-data parameters.
RELY shares fault-code data with Chery. Data may not cover RELY-specific systems.
Codes 8,313
| Code | Description | Brands | System |
|---|---|---|---|
| C04FC | Hydraulic pump | 1 | Chassis |
| C0513 | Right Rear Wheel Speed Sensor A Range/Performance | 14 | Chassis |
| C051D | Multi-axis acceleration sensor module 'A' missing calibration | 7 | Chassis |
| C0520 | Multi-axis Acceleration Sensor Module A | 13 | Chassis |
| C0522 | Multi-axis acceleration sensor module 'B' missing calibration | 11 | Chassis |
| C0523 | Multi-axis acceleration sensor module 'B' intermittent/erratic | 5 | Chassis |
| C0525 | Multi-axis acceleration sensor module 'B' | 5 | Chassis |
| C0529 | Steering angle sensor module missing calibration | 6 | Chassis |
| C052C | ABS Pump Motor Control Circuit/Open | 14 | Chassis |
| C0551 | Longitudinal acceleration sensor circuit/open | 12 | Chassis |
| C05CE | Brake master cylinder piston position sensor 'B' circuit voltage low | 10 | Chassis |
| C0825 | Control unit installation incorrect | 1 | Chassis |
| C1000 | Hill descent control function | 24 | Chassis |
| C1001 | Tandem brake master cylinder, pressure: Plausibility | 22 | Chassis |
| C1002 | RF of left rear TPMS communication failure | 17 | Chassis |
| C1003 | Vacuum supply: Leak detected | 19 | Chassis |
| C1004 | ABS operation fault | 19 | Chassis |
| C1005 | Torque sensor power voltage failure (in usual condition) | 20 | Chassis |
| C1006 | Motor terminal voltage failure [at abnormal condition failure] (#41) | 18 | Chassis |
| C1007 | Diag C I B U S C M T O | 20 | Chassis |
| C1008 | Diag C I B U S C M T O | 19 | Chassis |
| C1009 | Diag C I B U S C M B Z E2 E | 21 | Chassis |
| C1010 | Tandem brake master cylinder, pressure sensor 1: Signal offset | 22 | Chassis |
| C1011 | Tandem brake master cylinder, pressure sensor 2: Signal offset | 21 | Chassis |
| C1020 | Diaphragm travel sensor: Signal faulty | 16 | Chassis |
| C106378 | 1. When the radar reports an error and the DTC is read as (front radar not calibrated) through the diagnostic tool | 1 | Chassis |
| C108C | Reverse switch signal remaining too high/too low | 4 | Chassis |
| C1095 | Brake switch/lamp open circuit fault | 19 | Chassis |
| C1099 | Internal failure secondary shuttle valve | 17 | Chassis |
| C10AD | Vacuum sensor general fault | 2 | Chassis |
| C1100 | Power restart | 21 | Chassis |
| C1101 | Battery voltage high | 25 | Chassis |
| C1102 | Battery voltage low | 24 | Chassis |
| C1108 | Diag C I B U S C M T O | 18 | Chassis |
| C1109 | Diag C I B U S C M B Z E2 E | 19 | Chassis |
| C1111 | Control lateral acceleration | 25 | Chassis |
| C1112 | Hood hydraulic pump relay 1 | 23 | Chassis |
| C1113 | Hood Hydraulic Pump Relay 2 - J588 | 23 | Chassis |
| C1114 | Roll axis torque | 22 | Chassis |
| C1115 | rotary sensor input is abnormal | 23 | Chassis |
| C1121 | Damper solenoid | 23 | Chassis |
| C1122 | Front Latch Motor - Timeout | 23 | Chassis |
| C1123 | Steering isolation valve supply circuit | 21 | Chassis |
| C1124 | Exit DTC -41 | 21 | Chassis |
| C1130 | Hood solenoid 1 - N272 | 16 | Chassis |
| C1135 | Pull-up switch is stuck | 19 | Chassis |
| C1136 | Steering wheel angle information failure | 19 | Chassis |
| C1138 | Left-hand roll-over protection solenoid | 15 | Chassis |
| C1141 | Rear seat belt pre-tensioner - pass side | 22 | Chassis |
| C1151 | CAN Gearbox data failure | 18 | Chassis |
Some brand data is extracted from diagnostic files and may contain manufacturer-specific wording. General SAE J2012 descriptions are used where available.