Porsche fault codes
2,794 codes · 25 vehicle records · 190 ECU records · 0 live-data parameters
Codes 2,794
| Code | Description | Brands | System |
|---|---|---|---|
| P1582 | Idle adaptation at limit | 21 | Powertrain |
| P1583 | Cruise Direction CircuitHigh Voltage | 16 | Powertrain |
| P158B00 | Fuel pressure sensor, low pressure Faulty | 1 | Powertrain |
| P1590 | Neutral position switch circuit high input | 22 | Powertrain |
| P1591 | Neutral position switch circuit low input | 17 | Powertrain |
| P1592 | Vehicle data recorder data available | 20 | Powertrain |
| P1593 | DME: Activation, solenoid valve, intake manifold (DISA) | 21 | Powertrain |
| P1594 | Charging Sys Voltage Too Hi | 16 | Powertrain |
| P1595 | Speed Ctrl Solenoid Circs | 16 | Powertrain |
| P1599 | Engine stall detected | 13 | Powertrain |
| P159D | Oil level/temperature sensor: implausible signal; Mechanical failure | 13 | Powertrain |
| P15A0 | Neutral gear sensor: electrical malfunction; Defective | 13 | Powertrain |
| P15A1 | Neutral gear sensor: implausible signal | 12 | Powertrain |
| P15A100 | Diagnostic fault check to report canceled start | 3 | Powertrain |
| P15A2 | Neutral gear sensor: short to GND; Short to plus | 12 | Powertrain |
| P15A200 | Diagnostic fault check to report the plausibility error in Gearbox zero-position switch | 3 | Powertrain |
| P15A4 | Vehicle Sleep Mode active; Upper limit exceeded | 12 | Powertrain |
| P15A900 | No description available | 1 | Powertrain |
| P15AB00 | No description available | 1 | Powertrain |
| P15B700 | DFC for active Status of Inducement System | 3 | Powertrain |
| P15E200 | No description available | 1 | Powertrain |
| P1600 | Power supply (B+) terminal 15 low voltage | 31 | Powertrain |
| P1601 | ECU processor Analog/Digital Converter fault | 36 | Powertrain |
| P1602 | Control unit faulty | 35 | Powertrain |
| P1603 | Function monitoring, torque comparison | 35 | Powertrain |
| P1604 | Control unit faulty | 35 | Powertrain |
| P1605 | ECU processor fault | 37 | Powertrain |
| P1606 | ASW requests controller reset | 32 | Powertrain |
| P1607 | HW requests controller reset | 32 | Powertrain |
| P1608 | Clutch actuator high temperature | 32 | Powertrain |
| P1609 | Crash shutdown activated | 31 | Powertrain |
| P160A | ECU processor fault | 29 | Powertrain |
| P160B | A/D converter (system electronic failure) | 19 | Powertrain |
| P1610 | Linear power controller (LPC) fault | 38 | Powertrain |
| P1611 | Timeout time reached | 36 | Powertrain |
| P1612 | Immobilizer no or wrong signal | 39 | Powertrain |
| P1613 | Configuration fault | 36 | Powertrain |
| P1614 | Wrong transponder key | 36 | Powertrain |
| P1615 | Interactive Reprogramming Code - replace module | 36 | Powertrain |
| P1616 | Interactive Reprogramming Code - Diagnose Further | 35 | Powertrain |
| P1617 | CAN controller DPRAM (dual channel RAM) fault | 34 | Powertrain |
| P1618 | Check for the presence of DTC(Diagnostic Trouble Codes) P1616 and | 31 | Powertrain |
| P1619 | Short circuit to negative or open circuit | 33 | Powertrain |
| P161A | Glow plug control module not programmed | 23 | Powertrain |
| P161B | Control module torque performance | 24 | Powertrain |
| P161C | Tire size not programmed | 19 | Powertrain |
| P161D | Level 1 rqueI m safety due to shift lever | 21 | Powertrain |
| P161E | Engine friction estimates are too high | 20 | Powertrain |
| P161F | Assembly plant mode counter not programmed | 18 | Powertrain |
| P1620 | Short circuit to positive | 33 | Powertrain |
Some brand data is extracted from diagnostic files and may contain manufacturer-specific wording. General SAE J2012 descriptions are used where available.