Opel fault codes
15,060 codes · 16 vehicle records · 175 ECU records · 0 live-data parameters
Codes 15,060
| Code | Description | Brands | System |
|---|---|---|---|
| C1207 | Seat lumbar height switch - passenger's | 29 | Chassis |
| C1208 | Memory reading and writing error | 23 | Chassis |
| C1209 | Seat depth switch - passenger's | 20 | Chassis |
| C120A | Ignition signal lost | 11 | Chassis |
| C120C | Torque sensor power supply is seriously abnormal | 15 | Chassis |
| C120D | Steering angle invalid | 9 | Chassis |
| C120E | Steering angle not initialized | 9 | Chassis |
| C120F | Steering angle not calibrated | 12 | Chassis |
| C1210 | Fault - engine in running status | 29 | Chassis |
| C1211 | Attempt to restart assist at high speed | 29 | Chassis |
| C1212 | Vehicle speed signal not received | 26 | Chassis |
| C1213 | Seat squab adjustment switch - passenger's | 20 | Chassis |
| C1217 | Pump motor shorted to ground | 21 | Chassis |
| C1218 | Massage switch - passenger's | 16 | Chassis |
| C1219 | Memory set switch - passenger's | 18 | Chassis |
| C121C | Software configuration invalid | 10 | Chassis |
| C121D | Control Module Improper Shutdown | 10 | Chassis |
| C121E | RAM check error | 11 | Chassis |
| C121F | If CAN signals are not entered from the door module at the passenger's seat that controls the side mirror (indicator) in the passenger's seat, BSD ECU sets DTC and turns off BSD switch LED and inhibits system operation | 11 | Chassis |
| C1220 | Seat squab heater - front passenger's | 15 | Chassis |
| C1221 | Seat squab temperature sensor - passenger's | 21 | Chassis |
| C1222 | Seat depth motor - passenger's | 26 | Chassis |
| C1223 | Seat depth sensor - passenger's | 22 | Chassis |
| C1224 | Seat tilt motor - passenger's | 16 | Chassis |
| C1225 | Speed control relay - passenger's | 25 | Chassis |
| C1226 | Excessive RF Wheel Acceleration | 25 | Chassis |
| C1227 | Seat lumbar support/massage CM - passenger's | 16 | Chassis |
| C1228 | Excessive RR Wheel Acceleration | 15 | Chassis |
| C1229 | Torque and angle signal power supply failure | 12 | Chassis |
| C122A | ECU temperature too high | 8 | Chassis |
| C122B | Power torque output reduced due to low voltage | 8 | Chassis |
| C122E | Serious deviation between motor rotor position and sensor signal position during plausibility detection | 8 | Chassis |
| C122F | Serious deviation between rotor steering angle signal and rotor redundant steering angle signal | 10 | Chassis |
| C1230 | Seat height adjustment sensor - driver's | 12 | Chassis |
| C1231 | Control unit internal fault | 25 | Chassis |
| C1232 | Seat tilt adjustment sensor - passenger's | 15 | Chassis |
| C1233 | Seat height adjustment sensor - passenger's | 17 | Chassis |
| C1234 | Seat forward/rearward sensor - passenger's | 19 | Chassis |
| C1235 | Seat forward/rearward sensor - driver's | 19 | Chassis |
| C1236 | Vehicle speed signal invalid | 27 | Chassis |
| C1237 | This test guides the operator with setting the sensitivity of the microwave sensors and C1238 | 17 | Chassis |
| C1239 | Check the wiring between %ecu and HVAC Interface Module | 13 | Chassis |
| C123A | If C2206, and/or C2202 are active then continue, else if any other ABS DTCs are active correct those first before continuing | 11 | Chassis |
| C123B | Electronic Brake Control Module RAM Program Overflow | 10 | Chassis |
| C123C | Electronic Brake Control Module RAM Malfunction | 8 | Chassis |
| C123D | Electronic Brake Control Module Solenoid Valve Timeout | 7 | Chassis |
| C123E | Electronic Brake Control Module RAM Periodic Interrupt | 7 | Chassis |
| C123F | System Voltage Low | 7 | Chassis |
| C1240 | ABS received data invalid | 14 | Chassis |
| C1241 | FL outlet valve | 26 | Chassis |
Some brand data is extracted from diagnostic files and may contain manufacturer-specific wording. General SAE J2012 descriptions are used where available.