Land Rover fault codes
14,401 codes · 75 vehicle records · 2,749 ECU records · 47,114 live-data parameters
Codes 14,401
| Code | Description | Brands | System |
|---|---|---|---|
| C1071 | Hybrid master control unit (HCP) interface: Signal invalid | 12 | Chassis |
| C1072 | DSC interface: Signal invalid | 16 | Chassis |
| C1073 | Sensor system, hybrid brake actuation changeover (SBA): Adjustment necessary | 10 | Chassis |
| C1074 | Wheel Speed Sensor Missing - Front Right | 6 | Chassis |
| C1075 | Wheel Speed Sensor Missing - Front Left | 10 | Chassis |
| C1076 | Front Right Rebound Damper Solenoid - General Electrical Failure | 7 | Chassis |
| C1077 | Wheel Speed Sensor Missing - Rear Left | 5 | Chassis |
| C1078 | Wheel Speed Sensor Erratic - Front Right | 7 | Chassis |
| C1079 | ABS Manufacturing Rolling Road Mode Active - Event Information | 4 | Chassis |
| C107A | Wheel Speed Sensor Erratic - Rear Right | 5 | Chassis |
| C107B | Wheel Speed Sensor Erratic - Rear Left | 10 | Chassis |
| C107C | RCM Lateral Acceleration Sensor - Signal Invalid | 3 | Chassis |
| C107D | RCM Longitudinal Acceleration Sensor - Signal Invalid | 3 | Chassis |
| C107E | Wheel Speed Sensor Dropout Failure - Rear Right | 3 | Chassis |
| C107F | RCM Roll Rate Sensor - Signal Plausibility Failure | 3 | Chassis |
| C1080 | Hybrid brake actuation changeover (SBA): Undervoltage | 9 | Chassis |
| C1081 | Hybrid brake actuation changeover (SBA): Overvoltage | 12 | Chassis |
| C1082 | Hybrid brake actuation changeover (SBA) control unit, internal | 15 | Chassis |
| C1083 | Right Rear inlet valve failure | 12 | Chassis |
| C1084 | Left Front outlet valve failure | 6 | Chassis |
| C1085 | Right Front outlet valve failure | 9 | Chassis |
| C1086 | Left rear outlet valve failure | 8 | Chassis |
| C1087 | Right Rear outlet valve failure | 4 | Chassis |
| C1088 | ABS Pump Motor Driver Open | 4 | Chassis |
| C1089 | ABS Pump Motor Supply Open | 4 | Chassis |
| C108A | DRIVER MODE SWITCH Fixed | 2 | Chassis |
| C108B | Open Power switch for slip control | 3 | Chassis |
| C108C | Reverse switch signal remaining too high/too low | 4 | Chassis |
| C108D | ABS Open Pump Motor | 2 | Chassis |
| C108E | ABS Locked Pump Motor | 2 | Chassis |
| C108F | No description available | 2 | Chassis |
| C1090 | If -68 or P0634-4B are set repair these DTC's first | 10 | Chassis |
| C1091 | Brake pedal not applied in deceleration fault | 11 | Chassis |
| C1092 | Open Solenoid - Iso Rear Left | 5 | Chassis |
| C1093 | Brake pedal not deceleration application and previous ignition cycle fault | 7 | Chassis |
| C1094 | Brake pedal application always has no deceleration fault | 10 | Chassis |
| C1095 | Brake switch/lamp open circuit fault | 19 | Chassis |
| C1096 | Internal failure primary separation valve | 6 | Chassis |
| C1097 | Internal failure secondary separation valve | 5 | Chassis |
| C1098 | Internal failure primary shuttle valve | 5 | Chassis |
| C1099 | Internal failure secondary shuttle valve | 17 | Chassis |
| C1100 | Power restart | 21 | Chassis |
| C1101 | Battery voltage high | 25 | Chassis |
| C1102 | Battery voltage low | 24 | Chassis |
| C1103 | Longitudinal acceleration sensor electrical failure | 21 | Chassis |
| C1104 | Brake bedding mode | 17 | Chassis |
| C1105 | Brake lamp control | 18 | Chassis |
| C1106 | Tire Size Mismatch | 19 | Chassis |
| C1107 | Diag C I B U S C M T O | 19 | Chassis |
| C1108 | Diag C I B U S C M T O | 18 | Chassis |
Some brand data is extracted from diagnostic files and may contain manufacturer-specific wording. General SAE J2012 descriptions are used where available.