ISUZU(ZA) fault codes
Coverage shown is Isuzu data: 6,918 codes · 5 vehicle records · 107 ECU records · 0 live-data parameters.
ISUZU(ZA) shares fault-code data with Isuzu. Data may not cover ISUZU(ZA)-specific systems.
Codes 6,918
| Code | Description | Brands | System |
|---|---|---|---|
| C1026 | ABS Secondary Circuit Over Boost Pressure | 13 | Chassis |
| C1031 | Low-pressure sensor, signal 2: Electrical fault | 17 | Chassis |
| C1032 | Low-pressure sensor, plausibility | 19 | Chassis |
| C1033 | Isolation Switch 2 | 11 | Chassis |
| C1034 | Left switch | 11 | Chassis |
| C1035 | Right switch | 15 | Chassis |
| C1036 | Damper temperature | 14 | Chassis |
| C1037 | High voltage shutdown fault | 12 | Chassis |
| C1041 | 00 ayarlandı | 16 | Chassis |
| C1042 | Pump motor open fault | 17 | Chassis |
| C1043 | Clutch sensor 2 fault | 12 | Chassis |
| C1045 | Radio/CD unit | 13 | Chassis |
| C1046 | CD Changer | 15 | Chassis |
| C1047 | Performance degradation | 11 | Chassis |
| C1050 | Shutoff valve, pressure sensor: Electrical fault | 17 | Chassis |
| C1051 | Shutoff valve: Electrical fault | 15 | Chassis |
| C1052 | Shutoff valve: Plausibility | 12 | Chassis |
| C1054 | System functionality reduced by diagnostic request | 13 | Chassis |
| C1055 | Electronic Control Unit (ECU) Performance | 14 | Chassis |
| C1056 | Air Suspension -66 | 13 | Chassis |
| C1057 | System relay coil short to ground | 13 | Chassis |
| C1061 | Brake disc wear | 12 | Chassis |
| C1062 | Brake pedal travel sensor: Short circuit to earth | 7 | Chassis |
| C1063 | Brake pedal travel sensor: Short circuit after battery voltage | 11 | Chassis |
| C1071 | Hybrid master control unit (HCP) interface: Signal invalid | 12 | Chassis |
| C1072 | DSC interface: Signal invalid | 16 | Chassis |
| C1073 | Sensor system, hybrid brake actuation changeover (SBA): Adjustment necessary | 10 | Chassis |
| C1074 | Wheel Speed Sensor Missing - Front Right | 6 | Chassis |
| C1075 | Wheel Speed Sensor Missing - Front Left | 10 | Chassis |
| C1081 | Hybrid brake actuation changeover (SBA): Overvoltage | 12 | Chassis |
| C1082 | Hybrid brake actuation changeover (SBA) control unit, internal | 15 | Chassis |
| C1083 | Right Rear inlet valve failure | 12 | Chassis |
| C1084 | Left Front outlet valve failure | 6 | Chassis |
| C1085 | Right Front outlet valve failure | 9 | Chassis |
| C108B | Open Power switch for slip control | 3 | Chassis |
| C1094 | Brake pedal application always has no deceleration fault | 10 | Chassis |
| C1099 | Internal failure secondary shuttle valve | 17 | Chassis |
| C1100 | Power restart | 21 | Chassis |
| C1101 | Battery voltage high | 25 | Chassis |
| C1102 | Battery voltage low | 24 | Chassis |
| C1103 | Longitudinal acceleration sensor electrical failure | 21 | Chassis |
| C1104 | Brake bedding mode | 17 | Chassis |
| C1105 | Brake lamp control | 18 | Chassis |
| C1106 | Tire Size Mismatch | 19 | Chassis |
| C1107 | Diag C I B U S C M T O | 19 | Chassis |
| C1108 | Diag C I B U S C M T O | 18 | Chassis |
| C1109 | Diag C I B U S C M B Z E2 E | 19 | Chassis |
| C110A | Front vertical acceleration sensor | 14 | Chassis |
| C110B | Rear vertical acceleration sensor | 14 | Chassis |
| C110C | Electric power steering (EPS) internal fault - general fault | 12 | Chassis |
Some brand data is extracted from diagnostic files and may contain manufacturer-specific wording. General SAE J2012 descriptions are used where available.