Isuzu fault codes
6,918 codes · 5 vehicle records · 107 ECU records · 0 live-data parameters
Codes 6,918
| Code | Description | Brands | System |
|---|---|---|---|
| P1709 | SMG: Safety concept, level 3 | 24 | Powertrain |
| P170A | Clutch switch out of self-test range | 20 | Powertrain |
| P1710 | Sensor power failure | 31 | Powertrain |
| P1711 | Wheel speed signal 1 range/performance | 27 | Powertrain |
| P1712 | Front right wheel speed sensor signal malfunction (CAN) | 25 | Powertrain |
| P1713 | TFT Sensor In Range Failure Low Value | 24 | Powertrain |
| P1714 | Shift solenoid A inductive signature | 22 | Powertrain |
| P1715 | SMG: Hydraulic pressure loss in system | 34 | Powertrain |
| P1716 | SMG: Switch-on frequency, hydraulic unit | 30 | Powertrain |
| P1718 | Incorrect neutral gear ratio | 20 | Powertrain |
| P1720 | SMG: CAN bus error | 36 | Powertrain |
| P1721 | Gear 1 incorrect ratio | 27 | Powertrain |
| P1722 | Gearbox output speed 2 implausible signal | 25 | Powertrain |
| P1723 | Starter interlock signal: open circuit | 25 | Powertrain |
| P1724 | Gear 4 incorrect ratio | 22 | Powertrain |
| P1725 | Insufficient engine speed increase during self-test | 27 | Powertrain |
| P1726 | Wheel speed signal 4 range/performance | 27 | Powertrain |
| P1727 | Shift motor electric | 22 | Powertrain |
| P1728 | Shift motor mechanic | 27 | Powertrain |
| P1729 | Select motor electric | 20 | Powertrain |
| P1730 | Pump relay driver | 33 | Powertrain |
| P1731 | Gear 1, faulty gear ratio | 36 | Powertrain |
| P1733 | Throttle actuator control motor circuit high - positive side | 28 | Powertrain |
| P1734 | Throttle actuator control motor circuit low - negative side | 34 | Powertrain |
| P1735 | First gear switch circuit failure | 32 | Powertrain |
| P1736 | Gear ratio error in 2nd prime | 30 | Powertrain |
| P1739 | Transmission component slipping | 27 | Powertrain |
| P1740 | SMG: Activation, solenoid valve, clutch | 31 | Powertrain |
| P1741 | Engagement potentiometer | 28 | Powertrain |
| P1744 | Torque converter clutch system performance | 29 | Powertrain |
| P1745 | Line pressure control | 33 | Powertrain |
| P1747 | EGS: CAN timeout DME | 24 | Powertrain |
| P1748 | EGS: Engine overrevving lock | 21 | Powertrain |
| P1749 | EGS: No programming | 20 | Powertrain |
| P1750 | EGS: Batt. + supply | 33 | Powertrain |
| P1751 | Shift Solenoid A Perf | 24 | Powertrain |
| P1752 | Power supply malfunction | 26 | Powertrain |
| P1755 | Transmission control solenoid valve 1 control circuit high voltage - solenoid on | 20 | Powertrain |
| P175D | Gradient sensor self-learning incomplete | 10 | Powertrain |
| P175F | Gearbox system basic setting not executed | 11 | Powertrain |
| P1760 | Brake switch | 32 | Powertrain |
| P1761 | EGS: Solenoid, shiftlock | 31 | Powertrain |
| P1762 | Overdrive band failed off | 26 | Powertrain |
| P1767 | implausible signal or value | 26 | Powertrain |
| P1768 | Perf/Normal/Winter Mode Input | 25 | Powertrain |
| P1772 | Load Signal Stuck On | 25 | Powertrain |
| P1773 | Hydraulic Pressure Sensor 1 Too High | 25 | Powertrain |
| P1779 | Supply voltage missing | 23 | Powertrain |
| P1780 | EGS: Torque intervention | 30 | Powertrain |
| P1781 | Parking lock power relay circuit | 26 | Powertrain |
Some brand data is extracted from diagnostic files and may contain manufacturer-specific wording. General SAE J2012 descriptions are used where available.