Holden fault codes
15,866 codes · 57 vehicle records · 254 ECU records · 0 live-data parameters
Codes 15,866
| Code | Description | Brands | System |
|---|---|---|---|
| C1316 | Lateral acceleration sensor signal fault | 17 | Chassis |
| C1341 | Left rear oil inlet solenoid valve failure | 23 | Chassis |
| C1343 | Left rear oil outlet solenoid valve failure | 21 | Chassis |
| C1346 | Faulty rear right oil inlet solenoid valve | 14 | Chassis |
| C1348 | Right rear inlet and outlet solenoid valve failure | 12 | Chassis |
| C1351 | Left front oil inlet solenoid valve failure | 14 | Chassis |
| C1353 | Left front oil outlet solenoid valve failure | 14 | Chassis |
| C1356 | Faulty front right oil inlet solenoid valve | 12 | Chassis |
| C1358 | Right front oil outlet solenoid valve failure | 12 | Chassis |
| C1362 | Switching solenoid valve 1 fault | 21 | Chassis |
| C1367 | Switching solenoid valve 2 fault | 20 | Chassis |
| C1372 | Limit solenoid valve 1 fault | 20 | Chassis |
| C1377 | Limit solenoid valve 2 failure | 19 | Chassis |
| C1381 | Recirculation pump power failure | 20 | Chassis |
| C1382 | Recirculation pump power relay failure | 20 | Chassis |
| C1383 | Brake fluid level sensor fault | 20 | Chassis |
| C1384 | Brake pedal switch fault | 12 | Chassis |
| C1385 | Solenoid valve power relay failure | 22 | Chassis |
| C1386 | Solenoid valve power relay failure | 20 | Chassis |
| C1387 | Speed sensor signal failure | 22 | Chassis |
| C1391 | Engine torque not confirmed | 19 | Chassis |
| C1392 | Electronic stability program fault | 19 | Chassis |
| C1398 | Configuration fault (vehicle configuration error) | 22 | Chassis |
| C139A | Automatically releases electronic parking brake (EPB) | 11 | Chassis |
| C139B | Yaw rate sensor signal fault | 9 | Chassis |
| C139C | Clutch pedal sensor calibration failure | 9 | Chassis |
| C139D | Yaw rate sensor failure | 9 | Chassis |
| C139F | Clutch pedal sensor signal failure | 9 | Chassis |
| C13A1 | Clutch pedal sensor signal failure | 9 | Chassis |
| C13A2 | Clutch pedal sensor signal failure | 11 | Chassis |
| C13A4 | Factory fault (uneven road surface) | 9 | Chassis |
| C13A6 | Traction Control 'All-Terrain' Electronic Stability Program (ESP) Mode Failure | 11 | Chassis |
| C1400 | Abnormal reset performed by HW | 19 | Chassis |
| C1406 | Electric power steering (EPS) pump overheating | 23 | Chassis |
| C140B | Insufficient voltage in Start/Stop mode | 10 | Chassis |
| C140D | Rear left tire pressure high | 9 | Chassis |
| C1436 | Steering Wheel Angle Signal | 12 | Chassis |
| C1437 | F/W actuator terminal high VOLT | 12 | Chassis |
| C1445 | control. Clear DTC(Diagnostic Trouble Codes) after normal operation is restored | 12 | Chassis |
| C1449 | No description available | 8 | Chassis |
| C144A | ECU relay - failure | 7 | Chassis |
| C144B | ECU temperature sensor - component or system temperature too high | 8 | Chassis |
| C149B | No description available | 7 | Chassis |
| C149C | Torque Tube Fault | 7 | Chassis |
| C149D | Clutch Calibration Not Learned | 9 | Chassis |
| C14D3 | No description available | 8 | Chassis |
| C14D5 | No description available | 8 | Chassis |
| C1500 | suburban | 14 | Chassis |
| C1502 | Longitudinal acceleration sensor signal fault | 15 | Chassis |
| C1503 | Longitudinal acceleration sensor signal fault | 18 | Chassis |
Some brand data is extracted from diagnostic files and may contain manufacturer-specific wording. General SAE J2012 descriptions are used where available.