Mercedes-Benz fault codes
20,291 codes · 1,724 vehicle records · 258 ECU records · 56,350 live-data parameters
Search only Mercedes-Benz codes
Codes 20,291
| Code | Description | Brands | System |
|---|---|---|---|
| C0061FD | Ays1 signal is not available (not equipped) / HW problem | 1 | Chassis |
| C0061FE | Ay1 signal has an INIT status failure | 1 | Chassis |
| C0062 | Longitudinal Acceleration Sensor | 28 | Chassis |
| C006200 | The longitudinal acceleration sensor has a malfunction. | 1 | Chassis |
| C006202 | Ax signal is faulty (temporary) | 1 | Chassis |
| C00622B | Ax signal is faulty (permanent). | 1 | Chassis |
| C006249 | Longitudinal Acceleration Sensor | 1 | Chassis |
| C006254 | Lngsbeschleunigungssensor nicht kalibriert - fehlende Kalibrierung | 2 | Chassis |
| C006276 | long acc sensor plausi failure, Sensor 180deg missmounted - wrong mounting position | 1 | Chassis |
| C0062EE | Ax signal is faulty (permanent). | 1 | Chassis |
| C0062FC | AXS failure due to wrong assembly position of the sensor or sticking sensor element or sensitivity faults. | 1 | Chassis |
| C0062FD | Ax signal is not available (not equipped) / HW problem | 1 | Chassis |
| C0062FE | Ax signal has an INIT status failure | 1 | Chassis |
| C0062FF | Alternating Ax signal faults exceeds max. fault latency (100ms) | 1 | Chassis |
| C006328 | Sensor Cluster Gierrate Offsetfehler - signal bias level out of range / zero adjustment failure | 1 | Chassis |
| C006329 | Sensor Cluster Gierrate Signalfehler - signal invalid | 1 | Chassis |
| C0063FF | Yaw Rate sens signal was detected unplausible while AYC was not fully active. | 1 | Chassis |
| C006400 | Roll Rate Sensor | 1 | Chassis |
| C006500 | Vertical Acceleration Sensor | 2 | Chassis |
| C006A | Multi-axis Acceleration Sensor | 27 | Chassis |
| C006A04 | Sensor Cluster Internal Error - System Internal Failures | 1 | Chassis |
| C006A29 | Yrs1 signal value contains Invalid Value pattern | 1 | Chassis |
| C006A2A | Yrs1 signal is faulty (permanent). | 1 | Chassis |
| C006A45 | PowerOn Monitoring was not able to detect startup (PowerOnSelftest) of SensorCluster also resetting sensor via CAN failed | 1 | Chassis |
| C006A4A | Sensor ID comparison for Yrs Axs and Ays | 1 | Chassis |
| C006A4B | Detected sensor type do not correspond with system configuration settings | 1 | Chassis |
| C006A54 | Sensor Offset calibration for Axs and Ays | 2 | Chassis |
| C006AEC | Yrs1 signal is faulty (permanent). | 1 | Chassis |
| C006AED | Alternating Yrs1 signal faults exceeds max. fault latency (100ms) | 1 | Chassis |
| C006AEE | Detected sensor type do not correspond with system configuration settings | 1 | Chassis |
| C006AEF | Yrs1 signal is not available (not equipped) / HW problem | 1 | Chassis |
| C006AFA | Sensor Cluster Init Fehler | 1 | Chassis |
| C006AFB | Sensor Cluster Signal(s) sends SNA or initial value | 1 | Chassis |
| C006AFC | Sensor Cluster sync message failure | 1 | Chassis |
| C006AFD | Sensor Cluster Synchronisierungsfehler | 1 | Chassis |
| C006C4B | The traction system has a malfunction. Over Temperature | 1 | Chassis |
| C006C53 | Stability System is degraded to ABS backup | 1 | Chassis |
| C006C64 | Stability System | 2 | Chassis |
| C006C81 | The traction system has a malfunction. Incorrect data were received. | 1 | Chassis |
| C006C87 | The traction system has a malfunction. The message is missing. | 1 | Chassis |
| C007200 | The temperature of the brake disks is too high. | 2 | Chassis |
| C007204 | The temperature of the brake disks is too high. There is an internal fault. | 1 | Chassis |
| C007300 | plaus.failure 1 pressure sensor MC1 vers. BLS. BLS defect | 1 | Chassis |
| C007500 | Brake Light Switch, Plausibility BLS_H - BLS_L | 2 | Chassis |
| C007600 | brakelightswitch permanent high with silamemory | 1 | Chassis |
| C007700 | plaus.failure pressure sensor MC1 vers. BLS. BLS defect whilst AS active | 1 | Chassis |
| C0078 | Tire Diameter | 28 | Chassis |
| C007800 | Brake Light Switch, power supply undervoltage | 1 | Chassis |
| C008000 | Brake disc temperature modell is deactivated. | 2 | Chassis |
| C008100 | Brakes overheated during active braking by BMR or ACB. | 1 | Chassis |
Some brand data is extracted from diagnostic files and may contain manufacturer-specific wording. General SAE J2012 descriptions are used where available.