AUDI fault codes
Coverage shown is Volkswagen data: 3,421 codes · 292 vehicle records · 248 ECU records · 0 live-data parameters.
AUDI shares fault-code data with Volkswagen. Data may not cover AUDI-specific systems.
Codes 3,421
| Code | Description | Brands | System |
|---|---|---|---|
| C0920 | ABS/ESP Control Module | 4 | Chassis |
| C0945 | Side airbag igniter - Drivers | 2 | Chassis |
| C0946 | Side airbag igniter - Passengers | 1 | Chassis |
| C0947 | Left Hand Rear Side Airbag | 1 | Chassis |
| C0948 | Right Hand Rear Side Airbag | 2 | Chassis |
| C0964 | Engine control module | 2 | Chassis |
| C100301 | The cause for the entry is probably an electrical malfunction All wheel drive pump electrical error | 1 | Chassis |
| C100600 | Steuergerät Ventil EVHL elektrischer Fehler | 2 | Chassis |
| C100700 | Steuergerät Ventil AVHL elektrischer Fehler | 2 | Chassis |
| C100800 | Steuergerät Ventil EVHR elektrischer Fehler | 2 | Chassis |
| C100B07 | Fault Drive, parking brake right mechanical fault | 1 | Chassis |
| C100D01 | Fault Left parking brake drive mechanical fault is entered in the fault memory | 1 | Chassis |
| C100D11 | Fault Left parking brake motor voltage supply short to earth is entered in the fault memory | 1 | Chassis |
| C100D12 | Fault Left parking brake motor voltage supply short to positive is entered in the fault memory | 1 | Chassis |
| C100D13 | Fault Left parking brake motor voltage supply open circuit is entered in the fault memory | 1 | Chassis |
| C100F00 | Fault Left parking brake motor not moving freely is entered in the fault memory | 2 | Chassis |
| C101100 | Steuergerät Ventil MCI1 elektrischer Fehler | 3 | Chassis |
| C101214 | Fault Control unit left channel voltage supply | 1 | Chassis |
| C101229 | Fault Control unit left channel voltage supply | 1 | Chassis |
| C101504 | Brake electronics hydraulic unit defective | 1 | Chassis |
| C102AF0 | fault is present | 1 | Chassis |
| C102D | High friction inside power steering | 7 | Chassis |
| C1031F1 | Fault Adaptive suspension pressure sender - residual pressure for rear axle lowering too low is entered in the fault memory of the %str_steuergeraet | 1 | Chassis |
| C104400 | CAN2: Sensorcluster-Botschaft fehlt (CAN Timeout) | 3 | Chassis |
| C1045 | Radio/CD unit | 13 | Chassis |
| C1046 | CD Changer | 15 | Chassis |
| C1048 | Telephone Control Module | 9 | Chassis |
| C104AF0 | Eliminate the cause of event first. To do so, run the relevant test program from the test plan | 1 | Chassis |
| C1050 | Shutoff valve, pressure sensor: Electrical fault | 17 | Chassis |
| C1064 | Gearshift Interlock Switch | 5 | Chassis |
| C107701 | The event memory does not contain the DTC entries (ABS hydraulic/return flow pump, electrical malfunction) and C107704 | 1 | Chassis |
| C107704 | The event memory does not contain the DTC entries C107701 (ABS hydraulic/return flow pump, electrical malfunction) and | 1 | Chassis |
| C107E54 | DTC entry: -Headlights, no basic setting could not be deleted | 1 | Chassis |
| C107F54 | The DTC memory entry: - Headlights, no basic setting could not be deleted | 1 | Chassis |
| C10A700 | Roller mode detected | 2 | Chassis |
| C10AA29 | Steering moment sender implausible signal | 1 | Chassis |
| C10AA31 | Steering moment sender no signal | 1 | Chassis |
| C10AB01 | Supply voltage steering moment sender electrical fault | 1 | Chassis |
| C10ACF0 | Steering stop not adapted | 2 | Chassis |
| C10AE1B | Electro-mechanical power steering motor excessive resistance | 1 | Chassis |
| C10E5 | Compact Diagnostic Partner Not Available | 9 | Chassis |
| C10F029 | Steering moment sender 1 implausible | 1 | Chassis |
| C10F129 | Steering moment sender 2 implausible signal | 1 | Chassis |
| C110111 | Lane keeping assistant windscreen heater | 1 | Chassis |
| C110112 | Lane keeping assistant windscreen heater - short to positive | 1 | Chassis |
| C110115 | Lane keeping assistant windscreen heater - open circuit/short to positive | 1 | Chassis |
| C110300 | No fault relating to - ACC sensor misaligned - entered, but other faults are entered | 4 | Chassis |
| C110400 | Der MMR Front Slave meldet einen Fehler. | 4 | Chassis |
| C1106F0 | Dynamic calibration Limit value exceeded | 1 | Chassis |
| C110A54 | Fault - Camera control unit no basic setting is entered | 1 | Chassis |
Some brand data is extracted from diagnostic files and may contain manufacturer-specific wording. General SAE J2012 descriptions are used where available.