Ashok Leyland CV fault codes
11,027 codes · 19 vehicle records · 0 ECU records · 0 live-data parameters
Search only Ashok Leyland CV codes
Codes 11,027
| Code | Description | Brands | System |
|---|---|---|---|
| P25FA | Turbocharger/supercharger bypass valve 'C' control circuit high | 4 | Powertrain |
| P25FB | Turbocharger/supercharger bypass valve 'C' control circuit range/performance | 4 | Powertrain |
| P25FC | Turbocharger/supercharger bypass valve 'C' - mechanical | 4 | Powertrain |
| P25FD | Turbocharger/supercharger bypass valve 'C' temperature too high | 4 | Powertrain |
| P25FE | Supercharger Disconnect Clutch | 3 | Powertrain |
| P25FF | Electrical System Voltage Stabilizer Control Module Performance | 4 | Powertrain |
| P2600 | Gear P motor abnormal | 31 | Powertrain |
| P2601 | Motor always rotates | 33 | Powertrain |
| P2602 | Coolant Pump A Control Circuit Low | 32 | Powertrain |
| P2603 | Coolant Pump A Control Circuit High | 32 | Powertrain |
| P2604 | Steering angle range verification failed | 23 | Powertrain |
| P2605 | Motor short circuit | 23 | Powertrain |
| P2606 | Drive circuit short | 24 | Powertrain |
| P2607 | Relay stuck closed | 24 | Powertrain |
| P2608 | Current exceeds limit | 24 | Powertrain |
| P2609 | CAN receiving failure | 25 | Powertrain |
| P260A | PTO control circuit/open | 22 | Powertrain |
| P260B | PTO control circuit low | 22 | Powertrain |
| P260C | PTO control circuit high | 22 | Powertrain |
| P260D | PTO engaged lamp control circuit | 19 | Powertrain |
| P260E | Particulate Filter Regeneration Lamp Control Circuit | 16 | Powertrain |
| P260F | Evaporation system leak detection timeout | 22 | Powertrain |
| P2610 | Linear power controller (LPC) fault | 37 | Powertrain |
| P2611 | CPU data memory failure | 26 | Powertrain |
| P2612 | CPU is not working as expected | 24 | Powertrain |
| P2613 | CPU component internal error | 23 | Powertrain |
| P2614 | Camshaft A Position Signal Output Circuit/Open (Bank 1) | 31 | Powertrain |
| P2615 | Camshaft A Position Signal Output Circuit Low (Bank 1) | 29 | Powertrain |
| P2616 | Camshaft A Position Signal Output Circuit High (Bank 1) | 29 | Powertrain |
| P2617 | Crankshaft Position Signal Output Circuit/Open | 31 | Powertrain |
| P2618 | Crankshaft Position Signal Output Circuit Low | 29 | Powertrain |
| P2619 | Crankshaft Position Signal Output Circuit High | 29 | Powertrain |
| P261A | Coolant pump 'B' control circuit/open | 24 | Powertrain |
| P261B | Coolant Pump 'B' Control Circuit Range/Performance | 25 | Powertrain |
| P261C | Coolant Pump B Control Circuit Low | 27 | Powertrain |
| P261D | Coolant Pump B Control Circuit High | 27 | Powertrain |
| P261E | Coolant pump 'B' control circuit stuck on | 4 | Powertrain |
| P261F | Coolant pump 'A' control circuit stuck on | 12 | Powertrain |
| P2620 | Throttle position output circuit/open | 30 | Powertrain |
| P2621 | Throttle position output circuit low | 25 | Powertrain |
| P2622 | Throttle position output circuit high | 25 | Powertrain |
| P2623 | Injector control pressure regulator circuit/open | 26 | Powertrain |
| P2624 | Injector control pressure regulator circuit low | 23 | Powertrain |
| P2625 | Injector control pressure regulator circuit high | 24 | Powertrain |
| P2626 | O2 Sensor Pumping Current Trim Circuit/Open Bank 1 Sensor 1 | 33 | Powertrain |
| P2627 | O2 Sensor Pumping Current Trim Circuit Low Bank 1 Sensor 1 | 29 | Powertrain |
| P2628 | O2 Sensor Pumping Current Trim Circuit High Bank 1 Sensor 1 | 29 | Powertrain |
| P2629 | O2 Sensor Pumping Current Trim Circuit/Open Bank 2 Sensor 1 | 27 | Powertrain |
| P262A | Fuel injector - pilot injection not learned | 4 | Powertrain |
| P262B | Control module power off timer performance | 16 | Powertrain |
Some brand data is extracted from diagnostic files and may contain manufacturer-specific wording. General SAE J2012 descriptions are used where available.